Chair of Mechanics (400)

Organisational unit: Chair

101 - 200 out of 809Page size: 100

Research output

  1. 2021
  2. Published

    Numerical model for predicting liquid metal cracking during resistance spot welding of advanced high strength steels

    Prabitz, K. M., 2021, 12th International Conference on Zinc & Zinc Alloy Coated Steel Sheet - Galvatech.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  3. Published

    Simulation der thermischen Belastung blockgebremster Eisenbahnräder

    Scheinast, D., 2021

    Research output: Thesis › Master's Thesis

  4. Published

    Thermodynamic and kinetic modelling of the dissolution process of lime particles in BOF slags

    Ogris, D. M., Schenk, J. & Gamsjäger, E., 2021.

    Research output: Contribution to conference › Paper › peer-review

  5. Published

    Virtual System Evaluation of High Sensitive Pressure Sensor in Interaction with Printed Circuit Boards

    Veerappa Yalagach, M., 2021

    Research output: Thesis › Doctoral Thesis

  6. Published

    Wärmebehandlungssimulation von massiven Werkzeugen

    Schemmel, M., 2021

    Research output: Thesis › Doctoral Thesis

  7. 2020
  8. Published

    Transient phase fraction and dislocation density estimation from in-situ X-ray diffraction data with a low signal-to-noise ratio using a Bayesian approach to the Rietveld analysis

    Wiessner, M., Angerer, P., van der Zwaag, S. & Gamsjäger, E., 25 Dec 2020, In: Materials characterization. 172.2021, February, 9 p., 110860.

    Research output: Contribution to journal › Article › Research › peer-review

  9. Published

    Numerical analysis of a MEMS sensor's deformation behavior considering dynamic moisture conditions

    Yalagach, M., Fuchs, P. F., Antretter, T., Qi, T. & Weber, M., 2 Dec 2020, 2020 IEEE 22nd Electronics Packaging Technology Conference, EPTC 2020. Institute of Electrical and Electronics Engineers, p. 380-385 6 p. 9315091. (2020 IEEE 22nd Electronics Packaging Technology Conference, EPTC 2020).

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  10. Published

    On the treatment of non-reciprocal rate-independent kinetics via thermodynamic extremal principles

    Hackl, K., Fischer, F.-D. & Svoboda, J., Dec 2020, In: Journal of the mechanics and physics of solids. 145, p. 104149-1-7 7 p., 104149.

    Research output: Contribution to journal › Article › Research › peer-review

  11. Published

    Coupled damage variable based on fracture locus: Prediction of ductile failure in a complex structure

    Baltic, S., Magnien, J., Gänser, H.-P., Antretter, T. & Hammer, R., 23 Oct 2020, In: International journal of solids and structures. 207.2020, December, p. 132-144 13 p.

    Research output: Contribution to journal › Article › Research › peer-review

  12. Published

    Too much to ask for oder Wie ein Moodle Server bei laufender Prüfung in die Knie gezwungen wird

    Orthaber, M. & Antretter, T., 8 Oct 2020, <fnma> Magazin 03|2020. Graz, Vol. 03/2020.

    Research output: Chapter in Book/Report/Conference proceeding › Chapter › Education

  13. Published

    On an alternative approach for simulating chemically induced crack pattern evolutions in a single crystal

    Predan, J., Kegl, M., Abart, R., Fischer, F.-D. & Rammerstorfer, F. G., 1 Oct 2020, In: International journal of solids and structures. 202, p. 575-586 12 p., 202.

    Research output: Contribution to journal › Article › Research › peer-review

  14. Published

    Cycled hydrogen permeation through Armco iron – A joint experimental and modeling approach

    Drexler, A., Siegl, W., Ecker, W., Tkadletz, M., Klösch, G., Schnideritsch, H., Mori, G. K., Svoboda, J. & Fischer, F.-D., 23 Sept 2020, In: Corrosion science. 176.2020, November, 11 p., 109017.

    Research output: Contribution to journal › Article › Research › peer-review

  15. Published

    Evolution of a generic two-dimensional grain structure as a model for grain growth in microalloyed steels

    Gamsjäger, E. & Svoboda, J., 22 Sept 2020.

    Research output: Contribution to conference › Presentation › Research › peer-review

  16. Published

    Constraints in thermodynamic extremal principles for non-local dissipative processes

    Hackl, K., Fischer, F.-D. & Svoboda, J., 1 Sept 2020, In: Continuum Mechanics and Thermodynamics. 32, 5, p. 1337-1345 9 p., 32.

    Research output: Contribution to journal › Article › Research › peer-review

  17. Published

    Modelling of short-range ordering kinetics in dilute multicomponent substitutional solid solutions

    Svoboda, J., Holec, D., Popov, M., Zickler, G. & Fischer, F.-D., 2 Aug 2020, In: Philosophical magazine. 100.2020, 15, p. 1942-1961 20 p.

    Research output: Contribution to journal › Article › Research › peer-review

  18. Published

    EXAM-ON-DEMAND: SCHRIFTLICHE ONLINE-PRÜFUNGEN ALS ANTWORT AUF DEN LOCKDOWN

    Orthaber, M. & Antretter, T., 31 Jul 2020, fnma Magazin 02/2020 - E-Assessment und E-Examinations . Graz, Vol. 02/2020. p. 47 - 49 3 p.

    Research output: Chapter in Book/Report/Conference proceeding › Chapter › Education

  19. Published

    Concepts for E-Assessments in STEM on the Example of Engineering Mechanics: How to Assess Complex EngineeringProblemsElectronically

    Orthaber, M., Stütz, D., Antretter, T. & Ebner, M., 26 Jun 2020, In: International journal emerging technologies in learning : iJET. 15.2020, 12, p. 136-152 17 p.

    Research output: Contribution to journal › Article › Research › peer-review

  20. Published

    Local approach for coarsening of precipitates

    Svoboda, J., Shan, Y. V., Zickler, G. A., Kozeschnik, E. & Fischer, F.-D., 15 Mar 2020, In: Scripta materialia. 178.2020, 15 March, p. 232-235 4 p.

    Research output: Contribution to journal › Article › Research › peer-review

  21. Published

    Surface Energy of Au Nanoparticles Depending on Their Size and Shape

    Holec, D., Dumitraschkewitz, P., Vollath, D. & Fischer, F.-D., 8 Mar 2020, In: Nanomaterials. 10.2020, 3, p. 1-15 15 p., 484.

    Research output: Contribution to journal › Article › Research › peer-review

  22. Published

    Influence of Finite Mobilities of Triple Junctions on the Grain Morphology and Kinetics of Grain Growth

    Gamsjäger, E., Gschöpf, B. & Svoboda, J., 27 Jan 2020, In: Metals : open access journal . 10.2020, 18 p., 185.

    Research output: Contribution to journal › Article › Research › peer-review

  23. Published

    Model-Based Residual Stress Design in Multiphase Seamless Steel Tubes

    Leitner, S., Winter, G., Klarner, J., Antretter, T. & Ecker, W., 16 Jan 2020, In: Materials. 13.2020, 2, 12 p., 439.

    Research output: Contribution to journal › Article › Research › peer-review

  24. Published

    On solute depletion zones along grain boundaries during segregation

    Scheiber, D., Jechtl, T., Svoboda, J., Fischer, F.-D. & Romaner, L., 1 Jan 2020, In: Acta materialia. 182.2022, 1 January, p. 100-107 8 p.

    Research output: Contribution to journal › Article › Research › peer-review

  25. Published

    A Modeling Framework for Enhanced Reliability of Printed Circuit Boards and Power Electronics

    Gschwandl, M., 2020

    Research output: Thesis › Doctoral Thesis

  26. Published

    Bewertung numerischer Methoden für die Simulation von induktivem Erwärmen von Maschinenbauteilen

    Gschwentner, A., 2020

    Research output: Thesis › Master's Thesis

  27. Published

    Crossings – Deformation, Damage and Optimization

    Wiedorn, J., 2020

    Research output: Thesis › Doctoral Thesis

  28. Published

    Dilatometer experiments to determine the phase transformation kinetics and TRIP behavior for predeformed 20MnB8 steel sheets

    Tomasch, M., Ecker, W., Antretter, T. & Stockinger, M. (Publisher), 2020, XXXIX. Verformungskundliches Kolloquium, Tagungsband. Vol. 39. p. 72-77

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  29. Published

    Numerical analysis of a high speed large engine connecting rod

    Gschwandl, T. J., 2020

    Research output: Thesis › Master's Thesis

  30. Published

    Numerical Simulation of Crack Propagation during the Deformation of Galvanized PHS Sheets

    Hammer, P. J., 2020

    Research output: Thesis › Master's Thesis

  31. Published

    Residual stress evolution in low-alloyed seamless steel tubes: A simulation based approach on three different length scales

    Leitner, S., 2020

    Research output: Thesis › Doctoral Thesis

  32. 2019
  33. Published

    Constitutive modeling of anisotropic plasticity with application to fiber-reinforced composites

    Nagaraja, S. G., Pletz, M. & Schuecker, C., 15 Dec 2019, In: International journal of solids and structures. 180-181.2019, 15 December, p. 84-96 13 p.

    Research output: Contribution to journal › Article › Research › peer-review

  34. E-pub ahead of print

    The Emergence of Complexity from a Simple Model for Tissue Growth

    Dunlop, J. W. C., Zickler, G., Weinkamer, R., Fischer, F.-D. & Fratzl, P., 14 Dec 2019, (E-pub ahead of print) In: Journal of statistical physics. 2019, December, p. 1-15 15 p.

    Research output: Contribution to journal › Article › Research › peer-review

  35. Published

    Coupled damage variable based on fracture locus: Modelling and calibration

    Baltic, S., Magnien, J., Gänser, H.-P., Antretter, T. & Hammer, R., 23 Nov 2019, In: International journal of plasticity. 126.2020, March, 24 p., 102623.

    Research output: Contribution to journal › Article › Research › peer-review

  36. Published

    E-ASSESSMENT IN ENGINEERING MECHANICS: HOW DOES IT COMPARE TO CLASSICAL PAPER-PENCIL EXAMS?

    Orthaber, M., Antretter, T., Jurisits, R. & Schemmel, M., 11 Nov 2019, 12TH INTERNATIONAL CONFERENCE OF EDUCATION, RESEARCH AND INNOVATION (ICERI2019). p. 9381-9390

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  37. Published

    EXPERIENCES WITH A BLENDED LEARNING CONCEPT IN A FIRST YEAR ENGINEERING MECHANICS COURSE

    Orthaber, M., 11 Nov 2019, 12TH INTERNATIONAL CONFERENCE OF EDUCATION, RESEARCH AND INNOVATION (ICERI2019). p. 9229-9239

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  38. E-pub ahead of print

    Driving Forces on Dislocations - An Analytical and Finite Element Study

    Kolednik, O., Ochensberger, W., Predan, J. & Fischer, F.-D., 9 Nov 2019, (E-pub ahead of print) In: International journal of solids and structures. 190.2020, May, p. 181-198 18 p.

    Research output: Contribution to journal › Article › Research › peer-review

  39. E-pub ahead of print

    Are Onsager's reciprocal relations necessary to apply Thermodynamic Extremal Principles?

    Hackl, K., Fischer, F.-D., Zickler, G. & Svoboda, J., 8 Nov 2019, (E-pub ahead of print) In: Journal of the mechanics and physics of solids. 135.2020, February, 6 p., 103780.

    Research output: Contribution to journal › Article › Research › peer-review

  40. Published

    The creep behavior of a fully lamellar γ-TiAl based alloy

    Burtscher, M., Klein, T., Mayer, S., Clemens, H. & Fischer, F. D., 1 Nov 2019, In: Intermetallics. 114.2019, November, 9 p., 106611.

    Research output: Contribution to journal › Article › Research › peer-review

  41. Published

    Thermodynamic and mechanical stability of Ni3X-type intermetallic compounds

    Kulo, N., He, S., Ecker, W., Pippan, R., Antretter, T. & Razumovskiy, V. I., Nov 2019, In: Intermetallics. 114.2019, November, 9 p., 106604.

    Research output: Contribution to journal › Article › Research › peer-review

  42. E-pub ahead of print

    Damage tolerance of lamellar bone

    Razi, H., Predan, J., Fischer, F.-D. & Fratzl, P., 24 Oct 2019, (E-pub ahead of print) In: Bone. 130.2020, January, 7 p., 115102.

    Research output: Contribution to journal › Article › Research › peer-review

  43. Published

    Cyclic plastic deformation of rails in rolling/sliding contact –quasistatic FE calculations using different plasticity models

    Pletz, M., Meyer, K. A., Künstner, D., Scheriau, S. & Daves, W., 15 Oct 2019, In: Wear. 436-437.2019, 15 October, 10 p., 202992.

    Research output: Contribution to journal › Article › Research › peer-review

  44. Published

    Surface tension determines tissue shape and growth kinetics

    Ehrig, S., Schamberger, B., Bidan, C. M., West, A., Jacobi, C., Lam, K., Kollmannsberger, P., Petersen, A., Tomancak, P., Kommareddy, K., Fischer, F.-D., Fratzl, P. & Dunlop, J. W. C., 11 Sept 2019, In: Science Advances. 5.2019, 9, 8 p., eaav9394.

    Research output: Contribution to journal › Article › Research › peer-review

  45. Published

    Unifcation of the non-linear geometric transformation theory of martensite and crystal plasticity - Application to dislocated lath martensite in steels

    Petersmann, M., Antretter, T., Cailletaud, G., Sannikov, A., Ehlenbröker, U. & Fischer, F.-D., Aug 2019, In: International journal of plasticity. 119.2019, August, p. 140-155 16 p.

    Research output: Contribution to journal › Article › Research › peer-review

  46. Published

    Influence of misfit stress relaxation by power-law creep and plasticity on kinetics of coarsening of precipitates

    Svoboda, J., Yao, S., Kozeschnik, E. & Fischer, F.-D., 15 Jul 2019, In: Scripta materialia. 2019, Vol.168, p. 81-85 5 p.

    Research output: Contribution to journal › Article › Research › peer-review

  47. Published

    Investigation of deformation mechanisms in manganese steel crossings using FE models

    Wiedorn, J., Daves, W., Ossberger, U., Ossberger, H. & Pletz, M., 13 Jun 2019, In: Tribology International. 138.2019, October, p. 424-434 11 p.

    Research output: Contribution to journal › Article › Research › peer-review

  48. Published

    The Effect of Loading during Martensitic Transformation of a Margaging Steel after Prior Austenite Grain Size Refinement by Thermal Cycling

    Petersmann, M., Antretter, T., Sannikov, A., Sartory, B. & Ehlenbröker, U., 30 May 2019, In: Practical metallography = Praktische Metallographie. 56.2019, 6, p. 360-372 13 p.

    Research output: Contribution to journal › Article › Research › peer-review

  49. Published

    Kinetics of grain arrangements controlled by grain boundary and triple junction migration – Experiments and Modeling

    Gamsjäger, E. & Svoboda, J., 20 May 2019.

    Research output: Contribution to conference › Presentation › Research › peer-review

  50. Published

    Real-Time Measurement of Dynamic Wheel-Rail Contacts Using Ultrasonic Reflectometry

    Zhou, L., Brunskill, H., Pletz, M., Daves, W., Scheriau, S. & Lewis, R., 16 Apr 2019, In: Journal of Tribology. 141.2019, 6, 9 p., 061401.

    Research output: Contribution to journal › Article › Research › peer-review

  51. Published

    Debye-Einstein models for heat capacities of crystalline solids

    Gamsjäger, E. & Wießner, M., 8 Apr 2019.

    Research output: Contribution to conference › Presentation › Research › peer-review

  52. Published

    An improved engineering approach to assess crack arrays: an Addendum to Arch. Appl. Mech. 84 (2014) 1325–1337

    Kienzler, R., Fischer, F.-D. & Wessel, A., Apr 2019, In: Archive of applied mechanics. 89.2019, 4, p. 731 - 736 6 p.

    Research output: Contribution to journal › Article › Research › peer-review

  53. Published

    Deformation-induced phase transformation in a Co-Cr-W-Mo alloy studied by high-energy X-ray diffraction during in-situ compression tests

    Weißensteiner, I., Petersmann, M., Erdely, P., Stark, A., Antretter, T., Clemens, H. & Maier-Kiener, V., Feb 2019, In: Acta materialia. 164.2019, February, p. 272-282 11 p.

    Research output: Contribution to journal › Article › Research › peer-review

  54. Published

    A numerical modeling strategy for the damage-relevant evaluation of metrologically inaccessible thermo-mechanical milling tool loads

    Nemetz, A., 2019

    Research output: Thesis › Doctoral Thesis

  55. Published

    A Sequential Finite Volume Method / Finite Element Analysis of a Power Electronic Semiconductor Chip

    Gschwandl, M., Fuchs, P. F., Antretter, T., Pfost, M., Mitev, I., Tao, Q., Krivec, T., Schingale, A. & Decker, M., 2019, p. 1509-1514.

    Research output: Contribution to conference › Paper › peer-review

  56. Published

    Cyclic heat-up and damage-relevant substrate plastification of single- and bilayer coated milling inserts evaluated numerically

    Nemetz, A., Daves, W., Klünsner, T., Ecker, W., Schäfer, J., Czettl, C. & Antretter, T., 2019, In: Surface & coatings technology. 360.2019, February, p. 39-49 11 p.

    Research output: Contribution to journal › Article › Research › peer-review

  57. Published

    Development of a Simulation Method for the Evaluation of the Driving Dynamics of a Commercial Vehicle with Integrated E-Axle and Leaf Springs

    Bergmayr, T., 2019

    Research output: Thesis › Master's Thesis

  58. Published

    Diffusion-controlled crack propagation in alkali feldspar

    Petrishcheva, E., Rieder, M., Predan, J., Fischer, F.-D., Giester, G. & Abart, R., 2019, In: Physics and Chemistry of Minerals. 46.2019, 1, p. 15-26 12 p.

    Research output: Contribution to journal › Article › Research › peer-review

  59. Published

    Evolution of grain arrangements with finite grain boundary and triple junction mobility

    Gamsjäger, E. & Svoboda, J., 2019.

    Research output: Contribution to conference › Presentation › Research › peer-review

  60. Published

    Finite element model for predicting the initiation of subsurface damage in railway crossings—A parametric study

    Wiedorn, J., Daves, W., Ossberger, U., Ossberger, H. & Pletz, M., 2019, In: Proceedings of the Institution of Mechanical Engineers. Part F, Journal of rail and rapid transit. 2019, 6, p. Pages 614-628

    Research output: Contribution to journal › Article › Research › peer-review

  61. Published

    Improvement of the rail milling process & Evaluation of its potential for the reduction of rail defects

    Kubin, W., 2019

    Research output: Thesis › Doctoral Thesis

  62. Published

    Influence of bulk energy and triple junction mobility on interface kinetics - A tool for interpretation of experiments

    Hackl, K., Khan, A. U., Fischer, F.-D. & Svoboda, J., 2019, In: Acta materialia. 174.2019, August, p. 310-318 9 p.

    Research output: Contribution to journal › Article › Research › peer-review

  63. Published

    Kristallplastizitätsbasierte Finite Elemente Modellierung mikromechanischer Experimente

    Waldl, H., 2019

    Research output: Thesis › Master's Thesis

  64. Published

    Modelling of the post-treatment of coating/substrate architectures

    Faksa, L., 2019

    Research output: Thesis › Doctoral Thesis

  65. Published

    Multiphysics finite element simulation of resistance spot welding to evaluate liquid metal embrittlement in advanced high strength steels

    Prabitz, K. M., 2019, Mathematical Modelling of Weld Phenomena 12.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  66. Published

    Nonlinear material modeling and simulation of thermoplastics

    Morak, M. M., 2019

    Research output: Thesis › Doctoral Thesis

  67. Published

    Peak-Profilanalyse für In-situ-Hochtemperaturröntgenbeugung

    Ogris, D., 2019

    Research output: Thesis › Master's Thesis

  68. Published

    Residual stress and microstructure evolution in steel tubes for different cooling conditions – Simulation and verification

    Brunbauer, S., Winter, G., Antretter, T., Staron, P. & Ecker, W., 2019, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 747, p. 73-79

    Research output: Contribution to journal › Article › Research › peer-review

  69. Published

    Shot peening-induced plastic deformation of individual phases within a coated WC-Co hard metal composite material including WC plastification

    Faksa, L., Daves, W., Klünsner, T., Maier, K., Antretter, T., Czettl, C. & Ecker, W., 2019, In: Surface & coatings technology. 380.2019, 25 December, 11 p., 125026.

    Research output: Contribution to journal › Article › Research › peer-review

  70. Published

    Simulation des dynamischen/akustischen Verhaltens von Steuerkettentrieben

    Grinschgl, M., 2019

    Research output: Thesis › Doctoral Thesis

  71. Published

    Simulation of Phase Transformation and Material Plasticity for Press Hardening

    Tomasch, M., Ecker, W. & Antretter, T., 2019, Proceedings of NUMIFORM 2019: the 13th International Conference on Numerical Methods in Industrial Forming Processes. p. 362-365

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  72. Published

    Structure and surface energies of nanoparticles

    Holec, D., Fischer, F.-D. & Vollath, D., 2019.

    Research output: Contribution to conference › Presentation › Research › peer-review

  73. Published

    Thermally induced stress evolution in a Ti-43.5Al-4Nb-1Mo-0.1B electrode during melting in an atomization process

    Bialowas, J., 2019

    Research output: Thesis › Master's Thesis

  74. Published

    Wear of dry-running piston rod sealing rings: modelling and experiments

    Kaufmann, A., 2019

    Research output: Thesis › Doctoral Thesis

  75. 2018
  76. Published

    Crack arrest in thin metallic film stacks due to material- and residual stress inhomogeneities

    Kozic, D., Gänser, H.-P., Brunner, R., Kiener, D., Antretter, T. & Kolednik, O., 31 Dec 2018, In: Thin solid films. p. 14-22 9 p.

    Research output: Contribution to journal › Article › Research › peer-review

  77. Published

    Kinetics of interaction of impurity interstitials with dislocations revisited

    Svoboda, J., Ecker, W., Razumovskiy, V. I., Zickler, G. A. & Fischer, F.-D., Oct 2018, In: Progress in materials science. 101.2019, April, p. 172-206 35 p.

    Research output: Contribution to journal › Article › Research › peer-review

  78. Published

    The effect of loading during martensitic transformation of a maraging steel after prior austenite grain size refinement by thermal cycling

    Petersmann, M., Antretter, T. & Sannikov, A., 19 Sept 2018, Sonderbände der Praktischen Metallographie Band 52. p. 207-212 6 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  79. Published

    Sucker Rod String Design Optimization Using an Innovative Finite Element Simulation Approach

    Langbauer, C., Antretter, T. & Hofstätter, H., 1 Sept 2018, In: Oil gas European magazine. 44.2018, III, p. 126-132 7 p.

    Research output: Contribution to journal › Article › Research › peer-review

  80. Published

    Modelling blast fragmentation of cylinders of mortar and rock

    Iravani, A., Kukolj, I., Ouchterlony, F., Antretter, T. & Åström, J., Jun 2018, Fragblast 12: 12th International Symposium on Rock Fragmentation by Blasting. Schunnesson, H. & Johansson, D. (eds.). Luleå: Luleå Univ. of Technology, p. 597-610 15 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  81. Published

    Sucker Rod String Design Optimization using an Innovative Finite Elements Simulation Approach

    Langbauer, C., Hofstätter, H. & Antretter, T., 24 Apr 2018, NAFEMS Nordic Tagungsband 2018. p. 71-73

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  82. Published

    Sucker Rod String Design Optimization using an Innovative Finite Elements Simulation Approach

    Langbauer, C., Hofstätter, H. & Antretter, T., 19 Apr 2018, DGMK Tagungsbericht 2018. p. 227 237 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  83. Published

    Stress–strain analysis of the antiplane shear problem for an infinite cylindrical inclusion with eigenstrain: an addendum to Arch. Appl. Mech. 2018

    Fischer, F.-D., Zickler, G. A. & Svoboda, J., 2 Apr 2018, In: Archive of applied mechanics. 88.2018, 7, p. 1209-1211 3 p.

    Research output: Contribution to journal › Article › Research › peer-review

  84. Published

    Influence of accounting for translational motion of grains on grain growth kinetics and size distribution

    Svoboda, J. & Fischer, F.-D., 15 Mar 2018, In: Scripta Materialia. 146.2018, 15 March, p. 255-259 5 p.

    Research output: Contribution to journal › Article › Research › peer-review

  85. Published

    Low temperature heat capacities and thermodynamic functions described by Debye–Einstein integrals

    Gamsjäger, E. & Wießner, M., 25 Jan 2018, In: Monatshefte für Chemie = Chemical monthly. 149, p. 357-368 12 p.

    Research output: Contribution to journal › Article › Research › peer-review

  86. Published

    An innovative concept for interstitial diffusion in stressed crystals

    Svoboda, J., Zickler, G. A. & Fischer, F.-D., 2018, In: International journal of solids and structures. p. 173-180

    Research output: Contribution to journal › Article › Research › peer-review

  87. Published

    An In-Situ LSCM Study on Bainite Formation in a Fe-0.2C-1.5Mn-2.0Cr Alloy

    Sainis, S., Farahani, H., Gamsjäger, E. & van der Zwaag, S., 2018, In: Metals : open access journal . 8, 498, p. 1-22 22 p.

    Research output: Contribution to journal › Article › Research › peer-review

  88. Published

    Anisotropy of Interstitial Diffusion in bcc-crystals due to Stress-Induced Unequal Occupancies of Different Types of Sites

    Svoboda, J. & Fischer, F.-D., 2018, In: International journal of solids and structures. 152-153, p. 66-70

    Research output: Contribution to journal › Article › Research › peer-review

  89. Published

    Crystallography-microstructure-relations of hierarchical lath martensite from a micromechanical point of view

    Petersmann, M., 2018

    Research output: Thesis › Doctoral Thesis

  90. Published

    Deep drawing of press hardening steels

    Tomasch, M., Ecker, W., Kaiser, R. & Antretter, T., 2018, Journal of Physics: Conference Series. IOP Publishing Ltd., Vol. 1063. 012038

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  91. Published

    Designing nanoindentation simulation studies by appropriate indenter choices: Case study on single crystal tungsten

    Goel, S., Cross, G., Stukowski, A., Gamsjäger, E., Beake, B. & Agrawal, A., 2018, In: Computational materials science. 152, p. 196-210 15 p.

    Research output: Contribution to journal › Article › Research › peer-review

  92. Published

    Development of an automated preprocessor for the micromechanical modeling of foundry sands

    Ralph, B., 2018

    Research output: Thesis › Master's Thesis

  93. Published

    Elastic stress-strain analysis of an infinite cylindrical inclusion with eigenstrain

    Fischer, F.-D., Zickler, G. & Svoboda, J., 2018, In: Archive of applied mechanics. 88, p. 453-460

    Research output: Contribution to journal › Article › Research › peer-review

  94. Published

    Evaluation of Digital Image Correlation Techniques for the Determination of Coefficients of Thermal Expansion for Thin Reinforced Polymers

    Gschwandl, M., Frewein, M., Fuchs, P. F., Antretter, T., Pinter, G. G. & Novàk, P., 2018.

    Research output: Contribution to conference › Poster › Research

  95. Published

    Evaluation of Digital Image Correlation Techniques for the Determination of Coefficients of Thermal Expansion for Thin Reinforced Polymers

    Gschwandl, M., Frewein, M., Fuchs, P. F., Antretter, T., Pinter, G. G. & Novàk, P., 2018, EMAP 2018 Conference Proceedings. 4 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  96. Published

    Gradient polymer composites for optimum heat dissipation

    Marx, P., Morak, M., Gschwandl, M., Fuchs, P., Antretter, T., Pfost, M., Kern, W. & Wiesbrock, F., 2018, In: Journal of the American Chemical Society. 2, 1 p., PMSE-772.

    Research output: Contribution to journal › Meeting Abstract

  97. Published

    Grain growth controlled by grain boundary and boundary junction migration

    Ogris, D. & Gamsjäger, E., 2018.

    Research output: Contribution to conference › Poster › Research › peer-review

  98. Published

    Influene of accounting for translational motion of grains on grain growth kinetics and size distribution

    Svoboda, J. & Fischer, F.-D., 2018, In: Scripta materialia. 146, p. 225-259

    Research output: Contribution to journal › Article › Research › peer-review

  99. Published

    Kinetics of grain boundary networks controlled by triple junction and grain boundary mobility

    Gamsjäger, E., Ogris, D. & Svoboda, J., 2018, In: Metals : open access journal . 8, 977, p. 1 19 p.

    Research output: Contribution to journal › Article › Research › peer-review

  100. Published

    Kinetics of Grain Boundary Segregation in Multicomponent Systems – The Example of a Mo-C-B-O System

    Scheiber, D., Romaner, L., Fischer, F.-D. & Svoboda, J., 2018, In: Scripta materialia. 150, p. 110-114 5 p.

    Research output: Contribution to journal › Article › Research › peer-review

  101. Published

    Model Free Kinetics coupled with Finite Element Method for curing simulation of thermosetting epoxy resins

    Tao, Q., Pinter, G. G., Antretter, T., Krivec, T. & Fuchs, P., 2018, In: Journal of Applied Polymer Science. p. 1-8

    Research output: Contribution to journal › Article › Research › peer-review

  102. Published

    Modeling Dry Wear of Piston Rod Sealing Elements of Reciprocating Compressors Considering Gas Pressure Drop Across the Dynamic Sealing Surface

    Kaufmann, A., Lindner-Silwester, T. & Antretter, T., 2018, In: Journal of tribology (Transactions of the ASME).

    Research output: Contribution to journal › Article › Research › peer-review

  103. Published

    Numerical Analysis of Residual Stress and Crack Networks in CVD Multilayer Coated Cutting Tools

    Velic, D., 2018

    Research output: Thesis › Master's Thesis

  104. Published

    Surface energy of nanoparticles - influence of particle size and structures

    Vollath, D., Fischer, F.-D. & Holec, D., 2018, In: Beilstein journal of nanotechnology (Online-Ressource). 2018, 9, p. 2265-2276 12 p.

    Research output: Contribution to journal › Article › Research › peer-review

Previous 1 2 3 4 5 6 7 8 9 Next
View graph of relations

Contact information

Franz-Josef-Strasse 18/III, 8700 Leoben
  • Main phone number: +43 3842 402 4001