Chair of Polymer Processing (350)
Organisational unit: Chair
331 - 340 out of 946Page size: 10
Research output
- Published
Extrusion and Additive Manufacturing
Schuschnigg, S., Hentschel, L., Cano Cano, S. & Momeni, V., 15 Sept 2021.Research output: Contribution to conference › Poster › Research
- Published
Extrusion and Additive Manufacturing@ Institute of Polymer Processing
Schuschnigg, S., 22 May 2024. 1 p.Research output: Contribution to conference › Poster › Research
- Published
Fabrication and properties of extrusion-based 3D-printed hardmetal and cermet components
Lengauer, W., Duretek, I., Fürst, M., Schwarz, V., Gonzalez-Gutierrez, J., Schuschnigg, S., Kukla, C., Kitzmantel, M., Neubauer, E., Lieberwirth, C. & Morrison, V., 1 Aug 2019, In: International Journal of Refractory Metals and Hard Materials. 82.2019, August, p. 141-149 9 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Fabrication of multi-material dielectric elastomer actuators with the additive manufacturing process of material extrusion
Beier, P., 2024Research output: Thesis › Master's Thesis
- Published
Facile and Low-Cost Route for Sensitive Stretchable Sensors by Controlling Kinetic and Thermodynamic Conductive Network Regulating Strategies
Duan, L., D'hooge, D. R., Spörk, M., Cornillie, P. & Cardon, L., 29 May 2018, In: ACS Applied Materials & Interfaces. 10.2018, 26, p. 22678-22691 14 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Factors Affecting the Properties of POM-based Feedstocks for Fused Filament Fabrication/FFF
Kukla, C., Hentschel, L., Cano Cano, S., Kitzmantel, M., Holzer, C. & Gonzalez-Gutierrez, J., 5 Oct 2020. 6 p.Research output: Contribution to conference › Paper › peer-review
- Published
Fast Determination of Reinforcement in Polymer Nanocomposites
Kracalik, M., Laske, S., Gschweitl, M., Feuchter, M., Maier, G., Pinter, G., Friesenbichler, W. & Langecker, G., 2007, NanoEurope 2007. p. 13-14Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Feedstock Development for Material Extrusion of Aluminium: Printability and Debinding
Schuschnigg, S., Momeni, V. & Kukla, C., 21 Nov 2024, 32nd Leoben-Conference on Polymer Engineering and Science: New Materials New Perspectives. Leoben, Vol. 32. p. 132 1 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Feedstocks for metal injection moulding: Effect of particle charcateristics and binder composition on the rheological properties and the morphology of metal injection moulding feedstocks
Kukla, C. & Gonzalez-Gutierrez, J., 15 Nov 2017, WerWasWo.Forschung@MUL 2017. Schuschnigg, S. (ed.). 6 ed. Leoben, Austria, p. 127 1 p.Research output: Chapter in Book/Report/Conference proceeding › Chapter › Transfer
- Published
Feedstocks for the Shaping-Debinding-Sintering Process of Multi Material Components
Cano Cano, S., Kukla, C., Kaylani, D., Schuschnigg, S., Holzer, C. & Gonzalez-Gutierrez, J., 19 Apr 2018, p. 1. 1 p.Research output: Contribution to conference › Poster › Research
