Chair of Mechanical Engineering (140)
Organisational unit: Chair
521 - 530 out of 1,376Page size: 10
Research output
- Published
Development of a Flexible Program Architecture for Shape Optimization with Finite Elements
Kainzinger, P., 2009, 96 p.Research output: Thesis › Diploma Thesis › peer-review
- Published
Entwicklung eines Prüfstandes zur Prüfung von Kurbeltriebskomponenten von Verbrennungsmotoren unter betriebsnahen Bedingungen
Kaiser, T., 2006, 86 p.Research output: Thesis › Diploma Thesis
- Published
Influence of the levelling process on the mechanical properties of heavy steel plates
Kaltenbrunner, T., Antretter, T., Ecker, W., Kaiser, R., Gänser, H.-P. & Parteder, E., 2016, Proceedings of Rolling '16.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
A comprehensive methodology for criticality assessment of microvias in printed circuit board assemblies
Kamble, V. G., Patel, D. R., Schipfer, C., Thalhamer, A., Zuendel, J., Krivec, T., Antretter, T. & Fuchs, P. F., 2024, 2024 25th International Conference on Thermal, Mechanical and Multi-Physics Simulation and Experiments in Microelectronics and Microsystems, EuroSimE 2024. Institute of Electrical and Electronics Engineers, (2024 25th International Conference on Thermal, Mechanical and Multi-Physics Simulation and Experiments in Microelectronics and Microsystems, EuroSimE 2024).Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Auslegung und Optimierung von gefügten SLM-Bauteilen
Kapeindl, S., 2020Research output: Thesis › Master's Thesis
- Published
Effectiveness of improvised gas absorption techniques for emergency responders at releases of toxic gases
Kern, H., Taferner, M. & Raupenstrauch, H., 2013, 28th Center for Chemical Process Safety International Conference 2013, CCPS - Topical Conference at the 2013 AIChE Spring Meeting and 9th Global Congress on Process Safety. p. 1022-1028 7 p. (28th Center for Chemical Process Safety International Conference 2013, CCPS - Topical Conference at the 2013 AIChE Spring Meeting and 9th Global Congress on Process Safety; vol. 2).Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Alternative Kranteleskoparmkonzepte, Machbarkeitsstudie der vorgeschlagenen Varianten und neue Lösungen
Kessler, F. & Stoschka, M., 2000Research output: Book/Report › Commissioned report › Transfer › peer-review
- Published
Influence of T6 heat-treating and over-ageing on out-of-phase thermo-mechanical fatigue behaviors of Al-Si-Cu alloy
Khisheh, S., Azadi, M., Hendoabadi, V. Z., Parast, M. S. A., Winter, G., Seisenbacher, B., Grün, F. & Khalili, K., Dec 2022, In: Materials Today Communications. 33.2022, December, 12 p., 104803.Research output: Contribution to journal › Article › Research › peer-review
- Published
Residual stress state induced by high frequency mechanical impact treatment in different steel grades – Numerical and experimental study
Khurshid, M., Leitner, M., Barsoum, Z. & Schneider, C., 1 Apr 2017, In: International Journal of Mechanical Sciences. 123.2017, April, p. 34-42 9 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Methods and technologies for the processing of water-hydrocarbon emulsions and technogenic raw materials of metallurgical and petrochemical enterprises: A review
Khusnutdinov, S. I., Schenk, J., Khusnutdinov, I. S., Safiulina, A. F., Bazhin, V. Y. & Dubovikov, O. A., 2020, Topical Issues of Rational Use of Natural Resources 2019. Litvinenko, V. (ed.). p. 525-532 8 p. (Topical Issues of Rational Use of Natural Resources 2019; vol. 2).Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
