Chair of Designing Plastics and Composite Materials (250)
Organisational unit: Chair
31 - 40 out of 131Page size: 10
Research output
- Published
Dynamic Mechanical Response in Epoxy Nanocomposites Incorporating Various Nano-Silica Architectures
Chaudhary, S., Vryonis, O., Vaughan, A. S., Andritsch, T. & Feuchter, M., 2022, ICD 2022 - IEEE 2022 4th International Conference on Dielectrics, Proceedings. Institute of Electrical and Electronics Engineers, p. 86-89 4 p. (ICD 2022 - IEEE 2022 4th International Conference on Dielectrics, Proceedings).Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Effect of backbone selection on the solvent debinding of metal injection moulding feedstocks
Kukla, C., Cano, S., Schuschnigg, S., Holzer, C. & Gonzalez-Gutierrez, J., 2021, Euro PM2021 Congress Proceedings. (Euro PM2021 Congress Proceedings).Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Efficient 3d finite element modeling of cyclic elasto-plastic rolling contact
Meyer, K. A., Skrypnyk, R. & Pletz, M., Sept 2021, In: Tribology International. 161.2021, September, 12 p., 107053.Research output: Contribution to journal › Article › Research › peer-review
- E-pub ahead of print
Efficient Finite Element Modeling of Steel Cables in Reinforced Rubber
Pletz, M., Frankl, S. M. & Schuecker, C., 24 May 2022, (E-pub ahead of print) In: Journal of composites science. 6.2022, 6, 20 p., 152.Research output: Contribution to journal › Article › Research › peer-review
- Published
Efficient prediction of crack initiation from arbitrary 2D notches
Rettl, M., Pletz, M. & Schuecker, C., Jun 2022, In: Theoretical and Applied Fracture Mechanics. 119.2022, June, 16 p., 103376.Research output: Contribution to journal › Article › Research › peer-review
- Published
Effiziente Vorhersage der Rissinitiierung in porösen Materialien mit einem kombinierten Energie- und Spannungskriterium
Rettl, M., 2020Research output: Thesis › Master's Thesis
- Published
Ein Kunststofffenster zeigt Profil. Thermische und mechanische Optimierung eines Fensterrahmens
Wörndle, R., Fritz, M., Neumeyer, [. V. & Kitzmüller, [. V., 2003, In: Kunststoffe. p. 4-8Research output: Contribution to journal › Article › Research › peer-review
- Published
Enhancement of copper nanoparticle yield in magnetron sputter inert gas condensation by applying substrate bias voltage and its influence on thin film morphology
Knabl, F., Gutnik, D., Patil, P., Bandl, C., Vermeij, T., Pichler, C. M., Putz, B. & Mitterer, C., Dec 2024, In: Vacuum. 230, 113724.Research output: Contribution to journal › Article › Research › peer-review
- Published
Entwicklung eines FEM Modellierungsansatzes zur Beschreibung des Verformungsverhaltens von geflochtenen Kunststoffseilen
Fimbinger, N., 2019Research output: Thesis › Master's Thesis
- E-pub ahead of print
Evaluation of combinatorial algorithms for optimizing highly nonlinear structural problems
Rettl, M., Pletz, M. & Schuecker, C., 28 Apr 2023, (E-pub ahead of print) In: Materials and Design. 230.2023, June, 15 p., 111958.Research output: Contribution to journal › Article › Research › peer-review
