Materials and Design, ‎0264-1275

Journal

ISSNs0264-1275, 0261-3069
Additional searchable ISSN (electronic)1873-4197
51 - 60 out of 104Page size: 10

Research output

  1. 2020
  2. E-pub ahead of print

    Multi-method characterization approach to facilitate a strategy to design mechanical and electrical properties of sintered copper

    Wijaya, A., Eichinger, B., Chamasemani, F. F., Sartory, B., Hammer, R., Maier-Kiener, V., Kiener, D., Mischitz, M. & Brunner, R., 28 Sept 2020, (E-pub ahead of print) In: Materials and Design. 2021, 197, 11 p., 109188.

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    Open-cell tungsten nanofoams: Scaling behavior and structural disorder dependence of Young's modulus and flow strength

    Zhao, M., Schlueter, K., Wurmshuber, M., Reitgruber, M. & Kiener, D., 26 Sept 2020, In: Materials and Design. 2021, 197, 12 p., 109187.

    Research output: Contribution to journal › Article › Research › peer-review

  4. Published

    Nanoscale stress distributions and microstructural changes at scratch track cross-sections of a deformed brittle-ductile CrN-Cr bilayer

    Meindlhumer, M., Zalesak, J., Ecker, W., Rosenthal, M., Niese, S., Gawlitza, P., Hruby, H., Mitterer, C., Daniel, R., Keckes, J. & Todt, J., 5 Aug 2020, In: Materials & design. 195.2020, October, 16 p., 109023.

    Research output: Contribution to journal › Article › Research › peer-review

  5. Published

    Warm-forming of pre-aged Al-Zn-Mg-Cu alloy sheet

    Österreicher, J. A., Tunes, M. A., Grabner, F., Arnoldt, A., Kremmer, T., Pogatscher, S. & Schlögl, C. M., Aug 2020, In: Materials and Design. 193, p. 108837 1 p., 108837.

    Research output: Contribution to journal › Article › Research › peer-review

  6. Published

    An analytical solution for the correct determination of crack lengths via cantilever stiffness

    Alfreider, M., Kolitsch, S., Wurster, S. & Kiener, D., 27 Jun 2020, In: Materials and Design. 194.2020, September, 3 p., 108914.

    Research output: Contribution to journal › Article › Research › peer-review

  7. Published

    Fracture properties of thin film TiN at elevated temperatures

    Buchinger, J., Löfler, L., Ast, J., Wagner, A., Chen, Z., Michler, J., Zhang, Z., Mayrhofer, P. H., Holec, D. & Bartosik, M., 13 Jun 2020, In: Materials & design. 194.2020, September, p. 1-10 10 p., 108885.

    Research output: Contribution to journal › Article › Research › peer-review

  8. Published

    Room temperature recovery of cryogenically deformed aluminium alloys

    Gruber, B., Grabner, F., Falkinger, G., Schökel, A., Spieckermann, F., Uggowitzer, P. J. & Pogatscher, S., 23 May 2020, In: Materials & design. 193.2020, August, 108819.

    Research output: Contribution to journal › Article › Research › peer-review

  9. Published

    Thermally activated deformation mechanisms and solid solution softening in W-Re alloys investigated via high temperature nanoindentation

    Kappacher, J., Leitner, A., Kiener, D., Clemens, H. & Maier-Kiener, V., 1 Apr 2020, In: Materials and Design. 189.2020, April, 6 p., 108499.

    Research output: Contribution to journal › Article › Research › peer-review

  10. Published

    Microstructures, mechanical properties and deformation of near-rapidly solidified low-density Fe-20Mn-9Al-1.2C-xCr steels

    Zhang, J., Hu, C., Zhang, Y., LI, J., Song, C. & Zhai, Q., 15 Jan 2020, In: Materials and Design. 186.2020, 15 January, 13 p., 108307.

    Research output: Contribution to journal › Article › Research › peer-review

  11. 2019
  12. Published

    Influence of annealing on microstructure and mechanical properties of ultrafine-grained Ti45Nb

    Völker, B., Maier-Kiener, V., Werbach, K., Müller, T., Pilz, S., Calin, M., Eckert, J. & Hohenwarter, A., 5 Oct 2019, In: Materials and Design. 179.2019, 5 October, 11 p., 107864.

    Research output: Contribution to journal › Article › Research › peer-review

Previous 12 3 4 5 6 7 8 9 ...11 Next
View graph of relations