Research output

341 - 350 out of 838Page size: 10
rss feed
  1. 2013
  2. Published

    Ausnutzung der Scher- und Dehnerwärmung zur Heizzeitverkürzung; bei der Verarbeitung von Elastomeren

    Perko, L., Friesenbichler, W. & Fasching, M., 2013, In: Österreichische Kunststoff-Zeitschrift. p. 252-254

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    C-AFM and KPFM approach to inverstigate the electrical properties of single grain boundaries in ZnO varistor devices

    Nevosad, A., Hofstätter, M., Wiessner, M., Supancic, P. & Teichert, C., 2013, Proc. of SPIE, Oxide-based Materials and Devices IV. p. 1-10

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  4. Published

    Charge behavior on insulating monocrystallic surfaces by Kelvin probe force microscopy

    Mirkowska, M., Kratzer, M., Teichert, C. & Flachberger, H., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

  5. Published

    Charging behavior of the calcite (100) surface investigated by KPFM

    Mirkowska, M., Kratzer, M., Teichert, C. & Flachberger, H., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

  6. Published

    Correlation between Rheotens Measurements and Reinforcement of Polymer Nanocomposites in the Injection Molding Compounder

    Battisti, M., Duretek, I., Friesenbichler, W., Guttmann, P. & Pinter, G., 2013, 1st International Conference on Rheology and Modelling of Materials - Book of Abstracts. p. 39-39

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  7. Published

    Cross-linking of ROMP derived polymers using the two-photon induced thiol-ene reaction: towards the fabrication of 3D-polymer microstructures

    Grießer, T., Wolfberger, A., Daschiel, U., Schmidt, V., Fian, A., Jerrar, A., Teichert, C. & Kern, W., 2013, In: Polymer Chemistry. 4, p. 1708-1714

    Research output: Contribution to journal › Article › Research › peer-review

  8. Published

    DESIGN OF A DEMOLDING FORCE MEASUREMENT TOOL FOR INJECTION MOLDING

    Struklec, T., Burgsteiner, M., Lucyshyn, T., Balika, W., Moderegger, S. & Holzer, C., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

  9. Published

    Deformation Analysis of an Automotive Part by Injection Molding Simulation: Influence of Material Data and Mold Modeling on Prediction Quality

    Luger, H-J., Berger, G., Müller, F., Friesenbichler, W., Beytollahi, I. & Filz, P., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

  10. Published

    Deformation Analysis of an Automotive Part by Injection Molding Simulation: Influence of Material Data and Mold Modelling on Prediction Quality

    Luger, H-J., Berger, G., Müller, F., Friesenbichler, W., Beytollahi, I. & Filz, P., 2013, 29th International Conference of the Polymer Processing Society. p. 59-59

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  11. Published

    Design of a Demolding Force Measurement Tool for Injection Molding

    Struklec, T., Burgsteiner, M., Lucyshyn, T., Balika, W., Moderegger, S. & Holzer, C., 2013, Proceedings of the Polymer Processing Society 29th Annual Meeting ~ PPS-29. p. xxx-xxx

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

Previous 1...31 32 33 34 35 36 37 38 ...84 Next

Advanced filters

All authors

Reset

to
Reset filters