Nicole Mader

1 - 20 out of 32Page size: 20

Research output

  1. 2021
  2. Published

    Kautschukspritzgießen mit Qualitätserkennung: Automatische Prozessüberwachung mit iQ clamp control und maschinellem Lernen

    Hutterer, T., Berger-Weber, G., Kerschbaumer, R. C., Friesenbichler, W., Klutz, A., Leng, T. & Mayr, K., 3 May 2021, In: Kunststoffe. 111.2021, 5, p. 18 - 21 4 p.

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    Rubber Injection Molding with Quality Recognition

    Hutterer, T., Berger-Weber, G., Roman Christopher, K., Friesenbichler, W., Klutz, A., Leng, T. & Mayr, K., Apr 2021, In: Kunststoffe <München> / Kunststoffe international. 2021, 4, p. 6 - 9 4 p.

    Research output: Contribution to journal › Article › Research › peer-review

  4. 2020
  5. Published

    Causes of the Gloss Transition Defect on High-Gloss Injection-Molded Surfaces

    Gim, J., Han, E., Rhee, B., Friesenbichler, W. & Gruber, D. P., 15 Sept 2020, In: Polymers. 12.2020, 9, 16 p., 2100.

    Research output: Contribution to journal › Article › Research › peer-review

  6. Published

    Ultra-High Through-Cure of (Meth) Acrylate Copolymers via Photofrontal Polymerization

    Ebner, C., Mitterer, J., Eigruber, P., Stieger, S., Rieß, G. & Kern, W., 1 Jun 2020, In: Polymers. 12, 6, 1291.

    Research output: Contribution to journal › Article › Research › peer-review

  7. Published

    Viscoelastic Modelling of Polymer Melts and Rubber Compounds

    Friesenbichler, W., Stieger, S., Kerschbaumer, R. C., Berger-Weber, G., Neunhäuserer, A. & Mitsoulis, E., 2020, Advances in Polymer Processing 2020 Christian Hopmann Rainer Dahlmann Eds. Proceedings of the International Symposium on Plastics Technology. Springer Vieweg, p. 270-282 12 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  8. 2019
  9. E-pub ahead of print

    Comparison of steady-state and transient thermal conductivity testing methods using different industrial rubber compounds

    Kerschbaumer, R. C., Stieger, S., Gschwandl, M., Hutterer, T., Fasching, M., Lechner, B., Meinhart, L., Hildenbrandt, J., Schrittesser, B., Fuchs, P. F., Berger-Weber, G. & Friesenbichler, W., 26 Sept 2019, (E-pub ahead of print) In: Polymer Testing. 80.2019, December, p. 1-8 8 p., 106121.

    Research output: Contribution to journal › Article › Research

  10. Published

    Simulative and experimental investigation of rapid heat cycle molding for rubbers

    Hutterer, T., Berger-Weber, G., Mager, C., Fasching, M. A., Pacher, G. A. & Friesenbichler, W., 22 Jan 2019, AIP Conference Proceedings. Vol. 2055. p. 080003-1 - 080003-5 5 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  11. Published

    Thermal Degradation Kinetics of Polypropylene/Clay Nanocomposites Prepared by Injection Molding Compounder

    Kannan Vimalathithan, P., Barile, C., Casavola, C., Arunachalam, S., Battisti, M., Friesenbichler, W. & Vijayakumar, C. T., 1 Jan 2019, In: Polymer Composites. 2019, p. 1-10 10 p.

    Research output: Contribution to journal › Article › Research › peer-review

  12. Published

    Fault detection in rubber injection molding with multivariate statistics

    Hutterer, T., Berger-Weber, G. & Friesenbichler, W., 2019, In: Rubber world. 2019, December, p. 40-44 5 p.

    Research output: Contribution to journal › Article › Research › peer-review

  13. 2018
  14. Published

    A novel hyperbolic slit contraction with constant strain rate for elongational rheology of polymer melts

    Luger, H.-J., Löw-Baselli, B., Neunhäuserer, A., Friesenbichler, W. & Miethlinger, J., 9 Nov 2018, In: Polymer Testing. 73.2019, February, p. 104-114 11 p.

    Research output: Contribution to journal › Article › Research › peer-review

  15. Published

    Investigation on the Thermal Degradation Kinetics of Polypropylene/Organically Modified Montmorillonite Nanocomposites with Different Levels of Compatibilizer

    Vimalathithan, P. K., Barile, C., Casavola, C., Vijayakumar, C. T., Arunachalam, S., Battisti, M. & Friesenbichler, W., 9 Oct 2018, In: Macromolecular materials and engineering. 303.2018, December, 8 p., 1800260.

    Research output: Contribution to journal › Article › Research › peer-review

  16. Published

    Advanced Part Quality Testing – Compression Set vs. Non-Destructive and Fast Measurement Device JIDOKA S101 II

    Kerschbaumer, R., Lechner, B. & Friesenbichler, W., 2018.

    Research output: Contribution to conference › Poster › Research › peer-review

  17. Published

    A Model to Describe the Transient Temperature Build Up During Dosing of a Rubber Injection Molding Machine

    Kerschbaumer, R. & Friesenbichler, W., 2018.

    Research output: Contribution to conference › Paper › peer-review

  18. Published

    Determination of the temperature of an industrial rubber compound after dosing. A new ultrasound based method

    Hutterer, T., Praher, B., Berger-Weber, G. & Friesenbichler, W., 2018.

    Research output: Contribution to conference › Paper › peer-review

  19. Published

    Online detection of storage-induced changes of rubber properties in the injection molding process

    Hutterer, T., Fasching, M. A., Berger-Weber, G. & Friesenbichler, W., 2018.

    Research output: Contribution to conference › Paper › peer-review

  20. 2017
  21. Published

    Vorrichtung und Verfahren zum Faserspritzgießen von Spritzgussteilen

    Berger-Weber, G. (Inventor), Bevc, F. (Inventor), Bodor, C. (Inventor), Friesenbichler, W. (Inventor), Petschnig, A. (Inventor) & Schadler, W. (Inventor), 5 Apr 2017, IPC No. B29C45/00, B29K105/06, Patent No. EP3148765

    Research output: Patent

  22. 2016
  23. Published

    A PROCESS FOR PRODUCING SYNTHETIC PAPER AND PAPER THUS OBTAINED

    Laske, S. (Inventor), Langecker, G. R. (Inventor) & Friesenbichler, W. (Inventor), 14 Dec 2016, IPC No. B32B27/06, Patent No. EP2376284 (B1)

    Research output: Patent

  24. Published

    Vorrichtung und Verfahren zum Faserspritzgießen von Spritzgussteilen

    Friesenbichler, W. (Inventor), Bodor, C. (Inventor), Schadler, W. (Inventor) & Bevc, F. (Inventor), 18 Feb 2016, IPC No. B29C45/00, B29C45/33, Patent No. DE102014210295 A8

    Research output: Patent

  25. 2015
  26. Published

    DEVICE AND METHOD FOR FIBRE INJECTION MOULDING OF INJECTION MOULDED PARTS

    Berger-Weber, G. (Inventor), Bevc, F. (Inventor), Bodor, C. (Inventor), Friesenbichler, W. (Inventor), Petschnig, A. (Inventor) & Schadler, W. (Inventor), 3 Dec 2015, IPC No. B29C45/00, Patent No. WO2015181296

    Research output: Patent

  27. Published

    Vorrichtung und Verfahren zum Faserspritzgießen von Spritzgussteilen

    Friesenbichler, W. (Inventor), Bodor, C. (Inventor), Schadler, W. (Inventor), Bevc, F. (Inventor) & Petschnig, A. (Inventor), 3 Dec 2015, IPC No. B29C45/00, B29C45/33, Patent No. DE 10 2014 210 295 A8

    Research output: Patent

Previous 1 2 Next
View graph of relations

Latest Research Output

View more (32)