Nicole Mader
Research output
- 2021
- Published
Kautschukspritzgießen mit Qualitätserkennung: Automatische Prozessüberwachung mit iQ clamp control und maschinellem Lernen
Hutterer, T., Berger-Weber, G., Kerschbaumer, R. C., Friesenbichler, W., Klutz, A., Leng, T. & Mayr, K., 3 May 2021, In: Kunststoffe. 111.2021, 5, p. 18 - 21 4 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Rubber Injection Molding with Quality Recognition
Hutterer, T., Berger-Weber, G., Roman Christopher, K., Friesenbichler, W., Klutz, A., Leng, T. & Mayr, K., Apr 2021, In: Kunststoffe <München> / Kunststoffe international. 2021, 4, p. 6 - 9 4 p.Research output: Contribution to journal › Article › Research › peer-review
- 2020
- Published
Causes of the Gloss Transition Defect on High-Gloss Injection-Molded Surfaces
Gim, J., Han, E., Rhee, B., Friesenbichler, W. & Gruber, D. P., 15 Sept 2020, In: Polymers. 12.2020, 9, 16 p., 2100.Research output: Contribution to journal › Article › Research › peer-review
- Published
Ultra-High Through-Cure of (Meth) Acrylate Copolymers via Photofrontal Polymerization
Ebner, C., Mitterer, J., Eigruber, P., Stieger, S., Rieß, G. & Kern, W., 1 Jun 2020, In: Polymers. 12, 6, 1291.Research output: Contribution to journal › Article › Research › peer-review
- Published
Viscoelastic Modelling of Polymer Melts and Rubber Compounds
Friesenbichler, W., Stieger, S., Kerschbaumer, R. C., Berger-Weber, G., Neunhäuserer, A. & Mitsoulis, E., 2020, Advances in Polymer Processing 2020 Christian Hopmann Rainer Dahlmann Eds. Proceedings of the International Symposium on Plastics Technology. Springer Vieweg, p. 270-282 12 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- 2019
- E-pub ahead of print
Comparison of steady-state and transient thermal conductivity testing methods using different industrial rubber compounds
Kerschbaumer, R. C., Stieger, S., Gschwandl, M., Hutterer, T., Fasching, M., Lechner, B., Meinhart, L., Hildenbrandt, J., Schrittesser, B., Fuchs, P. F., Berger-Weber, G. & Friesenbichler, W., 26 Sept 2019, (E-pub ahead of print) In: Polymer Testing. 80.2019, December, p. 1-8 8 p., 106121.Research output: Contribution to journal › Article › Research
- Published
Simulative and experimental investigation of rapid heat cycle molding for rubbers
Hutterer, T., Berger-Weber, G., Mager, C., Fasching, M. A., Pacher, G. A. & Friesenbichler, W., 22 Jan 2019, AIP Conference Proceedings. Vol. 2055. p. 080003-1 - 080003-5 5 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Thermal Degradation Kinetics of Polypropylene/Clay Nanocomposites Prepared by Injection Molding Compounder
Kannan Vimalathithan, P., Barile, C., Casavola, C., Arunachalam, S., Battisti, M., Friesenbichler, W. & Vijayakumar, C. T., 1 Jan 2019, In: Polymer Composites. 2019, p. 1-10 10 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Fault detection in rubber injection molding with multivariate statistics
Hutterer, T., Berger-Weber, G. & Friesenbichler, W., 2019, In: Rubber world. 2019, December, p. 40-44 5 p.Research output: Contribution to journal › Article › Research › peer-review
- 2018
- Published
A novel hyperbolic slit contraction with constant strain rate for elongational rheology of polymer melts
Luger, H-J., Löw-Baselli, B., Neunhäuserer, A., Friesenbichler, W. & Miethlinger, J., 9 Nov 2018, In: Polymer Testing. 73.2019, February, p. 104-114 11 p.Research output: Contribution to journal › Article › Research › peer-review