Nicole Mader
Research output
- Published
Advanced Part Quality Testing – Compression Set vs. Non-Destructive and Fast Measurement Device JIDOKA S101 II
Kerschbaumer, R., Lechner, B. & Friesenbichler, W., 2018.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Thermal Degradation Kinetics of Polypropylene/Clay Nanocomposites Prepared by Injection Molding Compounder
Kannan Vimalathithan, P., Barile, C., Casavola, C., Arunachalam, S., Battisti, M., Friesenbichler, W. & Vijayakumar, C. T., 1 Jan 2019, In: Polymer Composites. 2019, p. 1-10 10 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Simulative and experimental investigation of rapid heat cycle molding for rubbers
Hutterer, T., Berger-Weber, G., Mager, C., Fasching, M. A., Pacher, G. A. & Friesenbichler, W., 22 Jan 2019, AIP Conference Proceedings. Vol. 2055. p. 080003-1 - 080003-5 5 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Online detection of storage-induced changes of rubber properties in the injection molding process
Hutterer, T., Fasching, M. A., Berger-Weber, G. & Friesenbichler, W., 2018.Research output: Contribution to conference › Paper › peer-review
- Published
Determination of the temperature of an industrial rubber compound after dosing. A new ultrasound based method
Hutterer, T., Praher, B., Berger-Weber, G. & Friesenbichler, W., 2018.Research output: Contribution to conference › Paper › peer-review
- Published
Fault detection in rubber injection molding with multivariate statistics
Hutterer, T., Berger-Weber, G. & Friesenbichler, W., 2019, In: Rubber world. 2019, December, p. 40-44 5 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Kautschukspritzgießen mit Qualitätserkennung: Automatische Prozessüberwachung mit iQ clamp control und maschinellem Lernen
Hutterer, T., Berger-Weber, G., Kerschbaumer, R. C., Friesenbichler, W., Klutz, A., Leng, T. & Mayr, K., 3 May 2021, In: Kunststoffe. 111.2021, 5, p. 18 - 21 4 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Rubber Injection Molding with Quality Recognition
Hutterer, T., Berger-Weber, G., Roman Christopher, K., Friesenbichler, W., Klutz, A., Leng, T. & Mayr, K., Apr 2021, In: Kunststoffe <München> / Kunststoffe international. 2021, 4, p. 6 - 9 4 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Causes of the Gloss Transition Defect on High-Gloss Injection-Molded Surfaces
Gim, J., Han, E., Rhee, B., Friesenbichler, W. & Gruber, D. P., 15 Sept 2020, In: Polymers. 12.2020, 9, 16 p., 2100.Research output: Contribution to journal › Article › Research › peer-review
- Published
Viscoelastic Modelling of Polymer Melts and Rubber Compounds
Friesenbichler, W., Stieger, S., Kerschbaumer, R. C., Berger-Weber, G., Neunhäuserer, A. & Mitsoulis, E., 2020, Advances in Polymer Processing 2020 Christian Hopmann Rainer Dahlmann Eds. Proceedings of the International Symposium on Plastics Technology. Springer Vieweg, p. 270-282 12 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
