Department Polymer Engineering and Science
Organisational unit: Departments and Institutes
Research output
- 2010
- Published
Hochglanzoberflächen beim Spritzgießen - Quantitative topografische Beurteilung der Formenstahl- und Kunststoffoberfläche
Berger, G., Friesenbichler, W., Reitter, M., Jutz, S. & Langecker, G., 2010, In: MP materials testing : Materialprüfung . 52, p. 211-221Research output: Contribution to journal › Article › Research › peer-review
- Published
Hochglanzoberflächen beim Spritzgießen. Quantitive topografische Beurteilung der Formenstahl- und Kunststoffoberfläche
Berger, G., Friesenbichler, W., Reitter, M., Jutz, S. & Langecker, G., 2010, In: MP materials testing : Materialprüfung . 52, p. 211-221Research output: Contribution to journal › Article › Research › peer-review
- Published
INVESTIGATIONS OF ADHESION ON TWO-SHOT MOULDED PARTS
Kisslinger, T., Lucyshyn, T., Doler, M., Langecker, G. & Holzer, C., 2010.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Implementation of an In-Situ Constrained Test Set Up for Rapid Gas Decompression Failure Analysis
Schrittesser, B., Major, Z., Olah, L. & Schwarz, T., 2010, Proceedings of 9th Fall Rubber Colloquium. p. 295-297Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
In-line Qualitätskontrolle mittels Nah-Infrarot Spektroskopie
Witschnigg, A., Laske, S. & Holzer, C., 2010, Proceedings - Grenzen von Kunststoffen neu definiert - Errungenschaften im Bereich Metallersatz und Leichtbau. p. 1-68Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
In-line characterization of polypropylene nanocomposites using FIT-NIR
Witschnigg, A., Laske, S., Kracalik, M., Feuchter, M., Pinter, G., Maier, G., Märzinger, W., Haberkorn, M., Langecker, G. & Holzer, C., 2010, In: Journal of Applied Polymer Science. 117, p. 3047-3053Research output: Contribution to journal › Article › Research › peer-review
- Published
Influence of Injection Molding Parameters and Aging on Geometry and Functionality of Plastic Targets for Mass Spectrometry
Pöhl, A., 2010, 108 p.Research output: Thesis › Master's Thesis
- Published
Influence of molecular structure on the extensional behaviour of polyethylene melts
Duretek, I., Florian, M. & Holzer, C., 2010, Book of Abstracts of ASPM 2010 Austrian-Slovenian Polymer Meeting. p. 130-130Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Influence of molecular structure on the extensional behaviour of polyethylene melts
Duretek, I., Florian, M. & Holzer, C., 2010.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Influence of organic dielectrics on the structure of Pentacene
Moser, A., Flesch, H-G., Neuhold, A., Edler, M., Grießer, T., Marchl, M., Trimmel, G., Golubkov, A., Haase, A., Smilgies, D-M., Zojer, E. & Resel, R., 2010.Research output: Contribution to conference › Poster › Research › peer-review
