Chair of Polymer Processing (350)
Organisational unit: Chair
271 - 280 out of 946Page size: 10
Research output
- Published
Production of multimaterial components by material extrusion - Fused filament fabrication (ME-FFF)
Kukla, C., Cano, S., Moritz, T., Müller-Köhn, A., Günther, A., Hampel, S. & Holzer, C., 2020, Euro PM 2018 Congress and Exhibition. (Euro PM 2018 Congress and Exhibition).Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Process validation and optimization of a two-step two-component direct bonding between thermoplastic and rubber
Huber, S., 2020Research output: Thesis › Master's Thesis
- Published
Process Optimization of Injection Overmolding Structural Electronics with Regard to Film Distortion
Hubmann, M., Madadnia, B., Groten, J., Pletz, M., Vanfleteren, J., Stadlober, B., Bossuyt, F., Kaur, J. & Lucyshyn, T., 22 Nov 2022, In: Polymers. 14.2022, 23, 20 p., 5060.Research output: Contribution to journal › Article › Research › peer-review
- Published
Process optimization and simulation of film insert molding for electronic applications
Hubmann, M., 2023Research output: Thesis › Doctoral Thesis
- Published
Processing Conditions of a Medical Grade Poly(Methyl Methacrylate) with the Arburg Plastic Freeforming Additive Manufacturing Process
Hentschel, L., Kynast, F., Petersmann, S., Holzer, C. & Gonzalez-Gutierrez, J., 2 Nov 2020, In: Polymers. 12, 11, p. 1-15 15 p., 2677.Research output: Contribution to journal › Article › Research › peer-review
- Published
Processability of Different Polymer Fractions Recovered from Mixed Wastes and Determination of Material Properties for Recycling
Möllnitz, S., Feuchter, M., Duretek, I., Schmidt, G., Pomberger, R. & Sarc, R., 31 Jan 2021, In: Polymers. 13.2021, 3, p. 1-43 43 p., 457.Research output: Contribution to journal › Article › Research › peer-review
- Published
Processability and mechanical properties of extensively recycled high density polyethylene
Oblak, P., Gonzalez-Gutierrez, J., Zupančič, B., Aulova, A. & Emri, I., 1 Jan 2015, In: Polymer Degradation and Stability. 114, p. 133-145 13 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Pressure dependent viscosity and its importance for injection molding simulations
Rajganesh Jegadeesan, X., Friesenbichler, W., Duretek, I., Filz, P. & Webelhaus, K., 2009, Conference Proceedings. p. 217-222Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Presentation of a Novel Sensor Based on Acoustic Emission in Injection Molding
Müller, F., Rath, G., Lucyshyn, T., Kukla, C., Burgsteiner, M. & Holzer, C., 2013, In: Journal of Applied Polymer Science. 127, p. 4744-4749Research output: Contribution to journal › Article › Research › peer-review
- Published
Preparation of Polymer-Nanocomposite-Masterbatch using a co-rotating twin screw extruder in combination with a melt pump
Laske, S., Kracalik, M., Feuchter, M., Maier, G., Pinter, G. & Langecker, G., 2008, PPS-24. p. 96-96Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
