Chair of Physical Metallurgy (420)
Organisational unit: Chair
Research output
- 2012
- Published
In situ study of the hot-working behavior of an advanced intermetallic multi-phase gamma-TiAl based alloy: HASYLAB Annual Report
Schwaighofer, E., Stark, A., Lottermoser, L., René, K., Clemens, H., Mayer, S. & Schell, N., 2012Research output: Non-textual form › Web publication/site › Research
- Published
In situ synchrotron radiation study during hot compressive deformation of a novel gamma TiAl alloy
Stark, A., Schwaighofer, E., Mayer, S., Lippmann, T., Lottermoser, L., Pyczak, F., Clemens, H. & Schreyer, A., 2012.Research output: Contribution to conference › Poster › Research › peer-review
- Published
In situ synchrotron study of B19 phase formation in an intermetallic gamma-TiAl alloy
Schmölzer, T., Stark, A., Schwaighofer, E., Lippmann, T., Mayer, S. & Clemens, H., 2012, In: Advanced engineering materials. 14, p. 445-448Research output: Contribution to journal › Article › Research › peer-review
- Published
Increased thermal stability of Ti-Al-N thin films by Ta alloying
Rachbauer, R., Holec, D. & Mayrhofer, P. H., 2012, In: Surface & coatings technology. 211, p. 98-103Research output: Contribution to journal › Article › Research › peer-review
- Published
Influence of heat treatments on the microstructure of a multi-phase titanium aluminide alloy
Schwaighofer, E., Schloffer, M., Schmölzer, T., Mayer, S., Lindemann, J., Guether, V., Klose, J. & Clemens, H., 2012, In: Practical metallography = Praktische Metallographie. 49, p. 124-137Research output: Contribution to journal › Article › Research › peer-review
- Published
Influence of proton irradiation on the precipitation kinetics and mechanical properties of intermetallic precipitation-hardened steel
Hofer, C., 2012, 62 p.Research output: Thesis › Diploma Thesis › peer-review
- Published
Influence of temperature and strain rate on dynamic softening processes in Allvac® 718Plus™
Mitsche, S., Sommitsch, C., Huber, D., Stockinger, M. & Poelt, P., 2012, THERMEC 2011. Trans Tech Publications, p. 2440-2445 6 p. (Materials Science Forum; vol. 706-709).Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Influence of tempering temperature on the corrosion behaviour of plastic mould steels X38CrMo16
Lerchbacher, C., Zinner, S. & Leitner, H., 2012, In: Berg- und hüttenmännische Monatshefte : BHM. 157, p. 414-419Research output: Contribution to journal › Article › Research › peer-review
- Published
Influence of the heating rate on the recrystallization behavior of molybdenum
Primig, S., Leitner, H., Knabl, W., Lorich, A., Clemens, H. & Stickler, R., 2012, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 535, p. 316-324Research output: Contribution to journal › Article › Research › peer-review
- Published
Interaction of heat checks in aluminum pressure casting dies and their effect on fatigue life
Raninger, P., Ecker, W., Antretter, T., Leindl, M. & Ebner, R., 2012, Key engineering materials. Vol. 488-489. p. 626-629 (Key engineering materials).Research output: Chapter in Book/Report/Conference proceeding › Chapter › Research
