Chair of Metal Forming (560)

Organisational unit: Chair

481 - 490 out of 731Page size: 10

Research output

  1. Published

    Ansätze für die Bewertung der Formänderungsverhältnisse beim Schrägwalzen

    Pschera, R., Klarner, J.K.-H. & Sommitsch, C., 2009, XXVIII. Verformungskundliche Kolloquium, 28.02-03.03.2009, Planneralm/Donnersbach. p. 215-228

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  2. Published

    FE-Modelling of the Cross-Rolling-Piercing Process with Discher Discs

    Pschera, R., Klarner, J.K.-H. & Sommitsch, C., 2007, 2nd International Conference Simuation and Modelling of Metallurgical Processes in Steelmaking. p. 313-317

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  3. Published

    Modellierung und Simulation des Schrägwalzens von Rundknüppeln zu Rohrluppen unter Berücksichtigung der Mikrostrukturentwicklung und der Umformbarkeit von Primärstrukturen

    Pschera, R., 2009

    Research output: Thesis › Doctoral Thesis

  4. Published

    Influence of TRIP on the residual stress development during heat treatment of high alloyed cast irons

    Raberger, R., Buchmayr, B. & Brandner, M., 2005, IDE200, Internationale Konferenz, Distortion Engineering. p. 365-371

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  5. Published

    Numerical simulation of the simultaneous precipitation of δ and γ′ phases in the Ni-base superalloy ATI Allvac®718 Plus™

    Radis, R., Zickler, G. A., Stockinger, M., Sommitsch, C. & Kozeschnik, E., 2010, 7th International Symposium on Superalloy 718 and Derivatives 2010. p. 569-578 10 p. (7th International Symposium on Superalloy 718 and Derivatives 2010; vol. 2).

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  6. Published

    Interaction of the precipitation kinetics of δ and γ' phases in nickel-base superalloy ATI Allvac® 718Plus™

    Radis, R., Zickler, G. A., Stockinger, M., Sommitsch, C. & Kozeschnik, E., 2010, THERMEC 2009. Chandra, T., Chandra, T., Chandra, T., Wanderka, N., Wanderka, N., Wanderka, N., Reimers, W., Reimers, W., Reimers, W., Ionescu, M., Ionescu, M. & Ionescu, M. (eds.). Trans Tech Publications, p. 2712-2717 6 p. (Materials Science Forum; vol. 638-642).

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  7. Published

    3D Finite Element Simulation of Pilger Mill Rolling

    Ragger, K., Kaiser, R., Hatzenbichler, T., Buchmayr, B., Paal, J. & Fluch, R., 2013,

    9th International Rolling Conferece & 6th European Rolling Conference,

    .     p. na-na

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  8. Published

    Modellierung des Kaltpilgerns – Betrachtung der Schädigungsentwicklung und ihre Beeinflussung durch die Vorformgeometrie

    Ragger, K., Kaiser, R., Paal, J., Fluch, R. & Buchmayr, B., 2014, In: Berg- und hüttenmännische Monatshefte : BHM. 159, p. 214-219

    Research output: Contribution to journal › Article › Research › peer-review

  9. E-pub ahead of print

    Cold pilgering of duplex steel tubes: The response of austenite and ferrite to excessive cold deformation up to high strains

    Ragger, K., Primig, S., Daniel, R., Kaiser, R., Paal, J., Mitterer, C. & Buchmayr, B., 16 Mar 2017, (E-pub ahead of print) In: Materials characterization. 128.2017, June, p. 257–268 12 p.

    Research output: Contribution to journal › Article › Research › peer-review

  10. Published

    Prozess- und Produktoptimierung zur Herstellung von kaltgepilgerten Rohren aus Edelstahl

    Ragger, K., 2016

    Research output: Thesis › Doctoral Thesis

Previous 1...45 46 47 48 49 50 51 52 ...74 Next
View graph of relations

Contact information

Franz-Josef Straße 18, 8700 Leoben