Chair of Mechanical Engineering (140)

Organisational unit: Chair

Research output

  1. 2020
  2. Published

    Local strain energy density approach to assess the fatigue strength of sharp and blunt V-notches in cast steel

    Schuscha, M., Leitner, M., Stoschka, M. & Meneghetti, G., 1 Mar 2020, In: International Journal of Fatigue. 132.2020, March, 105334.

    Research output: Contribution to journalArticleResearchpeer-review

  3. Published

    Investigation of fibre orientation and notch support of short glass fibre lot reinforced thermoplastics

    Stadler, G., Primetzhofer, A., Pinter, G. & Grün, F., 1 Feb 2020, In: International Journal of Fatigue. 131.2020, February, 8 p., 105284.

    Research output: Contribution to journalArticleResearchpeer-review

  4. Published
  5. Published

    Assessment of Shaft Surface Structures on the Tribological Behavior of Journal Bearings by Physical and Virtual Simulation

    Pusterhofer, M., Summer, F., Maier, M. & Grün, F., 15 Jan 2020, In: Lubricants. 8.2020, 1, 16 p.

    Research output: Contribution to journalArticleResearchpeer-review

  6. Published

    Close-to-Application Test Methodology Validated by a Baseline Study for Novel Bearing Developments in Aircraft Turbines

    Renhart, P., Summer, F., Grün, F. & Eder, A., 1 Jan 2020, In: Lubricants. 8, 1, p. 1-14 14 p., 7.

    Research output: Contribution to journalArticleResearchpeer-review

  7. Published

    Friction and Wear Performance of Various Polymer Coatings for Journal Bearings under Stop Start Sliding

    Summer, F., Grün, F. & Ravenhill, E. R., 1 Jan 2020, In: Lubricants. 8.2020, 1, 14 p., 1.

    Research output: Contribution to journalArticleResearchpeer-review

  8. Published
  9. Published

    Areal fatigue strength assessment of cast aluminium surface layers

    Pomberger, S., Stoschka, M., Aigner, R., Leitner, M. & Ehart, R., 2020, In: International Journal of Fatigue. 133.2020, April, 11 p., 105423.

    Research output: Contribution to journalArticleResearchpeer-review

  10. Published

    Auslegung und Optimierung von gefügten SLM-Bauteilen

    Kapeindl, S., 2020

    Research output: ThesisMaster's Thesis

  11. Published
  12. Published
  13. Published
  14. Published
  15. Published
  16. Published
  17. Published
  18. Published
  19. Published
  20. Published
  21. Published
  22. Published
  23. Published
  24. Published
  25. Published

    Methods and technologies for the processing of water-hydrocarbon emulsions and technogenic raw materials of metallurgical and petrochemical enterprises: A review

    Khusnutdinov, S. I., Schenk, J., Khusnutdinov, I. S., Safiulina, A. F., Bazhin, V. Y. & Dubovikov, O. A., 2020, Topical Issues of Rational Use of Natural Resources 2019. Litvinenko, V. (ed.). p. 525-532 8 p. (Topical Issues of Rational Use of Natural Resources 2019; vol. 2).

    Research output: Chapter in Book/Report/Conference proceedingConference contribution

  26. Published

    Numerical Fatigue Analysis of Induction-Hardened and Mechanically Post-Treated Steel Components

    Leitner, M., Aigner, R. & Grün, F., 2020, Advances in CAD/CAM/CAE Technologies. Multidisciplinary Digital Publishing Institute (MDPI)

    Research output: Chapter in Book/Report/Conference proceedingChapterResearch

  27. Published
  28. Published
  29. Published
  30. 2019
  31. E-pub ahead of print

    Fatigue crack growth in railway axle specimens – Transferability and model validation

    Simunek, D., Leitner, M., Rieger, M., Pippan, R., Gänser, H.-P. & Weber, F. J., 12 Dec 2019, (E-pub ahead of print) In: International Journal of Fatigue. 133.2020, 14 p., 105421.

    Research output: Contribution to journalArticleResearchpeer-review

  32. Published

    Development of a Model Test System for a Piston Ring/Cylinder Liner-Contact with Focus on Near-to-Application Seizure Behaviour

    Pusterhofer, M., Summer, F., Wuketich, D. & Grün, F., 22 Nov 2019, In: Lubricants. 7.2019, 12, p. 104-115 12 p., 104.

    Research output: Contribution to journalArticleResearchpeer-review

  33. Published
  34. Published

    Thermomechanical fatigue testing of dual hardening tool steels

    Hofinger, M., Seisenbacher, B., Ognianov, M., Leitner, H., Turk, C., Kapp, M. & Schnitzer, R., 19 Nov 2019, In: Steel research international. p. 1-9

    Research output: Contribution to journalArticleResearchpeer-review

  35. Published

    Crack Initiation and Propagation Fatigue Life of Ultra High-Strength Steel Butt Joints

    Ottersböck, M., Leitner, M., Stoschka, M. & Maurer, W., 1 Nov 2019, In: Applied Sciences : open access journal. 9.2019, 21, 4590.

    Research output: Contribution to journalArticleResearchpeer-review

  36. Published
  37. Published
  38. Published

    Influence of surface roughness on additively manufactured aluminum components

    Springer, S., Schneller, W., Leitner, M. & Grün, F., 26 Sept 2019.

    Research output: Contribution to conferencePosterResearch

  39. Published

    Influence of surface roughness on additively manufactured aluminum components

    Springer, S., Schneller, W., Leitner, M. & Grün, F., 24 Sept 2019, 36th Danubia Adria Symposium on Advances in Experimental Mechanics: Extended Abstracts. Plzen, Czech Republic, p. 105-106

    Research output: Chapter in Book/Report/Conference proceedingConference contribution

  40. Published

    On the behaviour of non-propagating cracks in steel and aluminium castings

    Schuscha, M., Aigner, R., Pomberger, S., Oberreiter, M., Leitner, M. & Stoschka, M., 17 Sept 2019, In: Engineering Fracture Mechanics. 220.2019, 15 October, 106670.

    Research output: Contribution to journalArticleResearchpeer-review

  41. Published

    Cast surface texture characterisation via areal roughness

    Pomberger, S., Stoschka, M. & Leitner, M., 12 Sept 2019, In: Precision Engineering. 60.2019, p. 465-481 17 p.

    Research output: Contribution to journalArticleResearchpeer-review

  42. Published

    Fretting behavior of thermoplastic polyurethanes

    Wang, C., Hausberger, A., Berer, M., Pinter, G., Grün, F. & Schwarz, T., 23 Aug 2019, In: Lubricants. 7.2019, 9, 24 p., 73.

    Research output: Contribution to journalArticleResearchpeer-review

  43. Published

    Correlation of Tribological Behavior and Fatigue Properties of Filled and Unfilled TPUs

    Wang, C., Stiller, T., Hausberger, A., Pinter, G., Grün, F. & Schwarz, T., 20 Jul 2019, In: Lubricants. 7.2019, p. 1-18 18 p.

    Research output: Contribution to journalArticleResearchpeer-review

  44. Published

    Damage models of different hardness layers subjected to point contact

    Trausmuth, A., Godor, I. & Grün, F., 15 Jul 2019, In: Wear. 430-431.2019, July, p. 157-168 12 p.

    Research output: Contribution to journalArticleResearchpeer-review

  45. Published

    A baseline study for developing novel coatings for high performance journal bearings in aircraft-turbines

    Renhart, P., Summer, F. & Grün, F., 13 Jun 2019, ECOTRIB 2019. Österreichische Tribologische Gesellschaft, p. 70 1 p.

    Research output: Chapter in Book/Report/Conference proceedingConference contribution

  46. Published
  47. Published
  48. Published

    On the Statistical Size Effect of Cast Aluminium

    Aigner, R., Pomberger, S., Leitner, M. & Stoschka, M., 14 May 2019, In: Materials. 12.2019, 10, 19 p., 1578.

    Research output: Contribution to journalArticleResearchpeer-review

  49. Published

    Numeric modeling of induction hardened boundary layers

    Aigner, R., 8 May 2019, Proceedings International FEMFAT User Meeting 2019: Fatigue Analysis of Joint Connections.

    Research output: Chapter in Book/Report/Conference proceedingConference contribution

  50. Published

    Application of different simulation approaches to numerically optimize high-frequency mechanical impact (HFMI) post-treatment process

    Ernould, C., Schubnell, J., Farajian, M., Maciolek, A., Simunek, D., Leitner, M. & Stoschka, M., 1 May 2019, In: Welding in the world. 63.2019, 3, p. 725-738 14 p.

    Research output: Contribution to journalArticleResearchpeer-review

  51. Published

    Analysis of fatigue notch effect due to axial misalignment for ultra high-strength steel butt joints

    Ottersböck, M., Leitner, M., Stoschka, M. & Maurer, W., May 2019, In: Welding in the world. 63.2019, 3, p. 851-865 15 p.

    Research output: Contribution to journalArticleResearchpeer-review

  52. Published

    Evaluation of surface roughness parameters and their impact on fatigue strength of Al-Si cast material

    Pomberger, S., Leitner, M. & Stoschka, M., May 2019, In: Materials Today: Proceedings. 12.2019, 2, p. 225-234 10 p.

    Research output: Contribution to journalArticleResearchpeer-review

Previous 1 2 3 4 5 6 7 8 ...28 Next