Chair of Functional Materials and Materials Systems (425)
Organisational unit: Chair
Research output
- Published
A comparative study on NbOx films reactively sputtered from sinterd and cold gas sprayed targets
Lorenz, R., O`Sullivan, M., Fian, A., Sprenger, D., Lang, B. & Mitterer, C., 2018, In: Applied surface science. p. 1157-1162Research output: Contribution to journal › Article › Research › peer-review
- Published
A comparative study on Ti1-xAlxN coatings reactively sputtered from compound and from mosaic targets
Schalk, N., Weirather, T., Polzer, C., Polcik, P. & Mitterer, C., 2011, In: Surface & coatings technology. 205, p. 4705-4710Research output: Contribution to journal › Article › Research › peer-review
- Published
A Comparison of 90° Bending for Foldable Electronics
Cordill, M. J., Kreiml, P., Köstenbauer, H. & Mitterer, C., 11 Jan 2024, In: Coatings. 14.2024, 1, 18 p., 98.Research output: Contribution to journal › Article › Research › peer-review
- Published
A comprehensive study on the metallographic preparation of W-Re samples for high resolution electron-based microscopy
Sommerauer, M., Clemens, H., Maier-Kiener, V. & Siller, M., 2023, Pract. Metallograp.. Vol. 60. p. 171-186Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- E-pub ahead of print
A correlative experimental and ab initio approach to improve the fracture behavior of Mo thin films by alloying with Cu
Jörg, T., Music, D., Cordill, M., Franz, R., Köstenbauer, H., Linke, C., Winkler, J., Schneider, J. M. & Mitterer, C., 25 Sept 2017, (E-pub ahead of print) In: Applied physics letters. 111.2017, 13, p. 134101-1-134101-4Research output: Contribution to journal › Article › Research › peer-review
- Published
A correlative experimental and theoretical investigation of phase formation and thermal stability of a quaternary Cr0.69Ta0.20B0.11N coating
Kainz, C., Patterer, L., Bogdanovski, D., Salman, S. A., Letofsky-Papst, I., Pohler, M., Czettl, C., Schneider, J. M., Mitterer, C. & Schalk, N., Dec 2023, In: Materialia. 32.2023, December, 9 p., 101931.Research output: Contribution to journal › Article › Research › peer-review
- Published
Additive manufacturing of 3D yttria-stabilized zirconia microarchitectures
Winczewski, J. P., Zeiler, S., Gabel, S., Maestre, D., Merle, B., Gardeniers, J. G. E. & Susarrey-Arce, A., 1 Feb 2024, In: Materials and Design. 238.2024, February, 11 p., 112701.Research output: Contribution to journal › Article › Research › peer-review
- Published
Additive manufacturing of magnesium alloy using uniform droplet spraying: modeling of microstructure evolution
Jaffar, S. M., Kostoglou, N., Fukuda, H., Rebholz, C., Ando, T., Liao, Y. & Doumanidis, C. C., Jun 2021, In: MRS Advances. 6, 15, p. 391-403 13 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Adhesion evaluation of thin films to dielectrics in multilayer stacks: A comparison of four-point bending and stressed overlayer technique.
Lassnig, A., Putz, B., Hirn, S., Többens, D., Mitterer, C. & Cordill, M. J., 15 Feb 2021, In: Materials and Design. 200, 15 February, 8 p., 109451.Research output: Contribution to journal › Article › Research › peer-review
- Published
Adhesion of polymers to hard coatings
Rebelo De Figueiredo, M., Bergmann, C., Ganser, C., Teichert, C. & Mitterer, C., 2012.Research output: Contribution to conference › Poster › Research › peer-review
