Research output

361 - 370 out of 623Page size: 10
rss feed
  1. 2013
  2. Published

    Adhesion tendency of polymers to hard coatings

    Rebelo De Figueiredo, M., Bergmann, C., Ganser, C., Teichert, C., Kukla, C. & Mitterer, C., 2013, In: International polymer processing. 28, 4, p. 415-420 6 p.

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    Application and Development of Simulation Software in Polymer Processing

    Lucyshyn, T., Müller, F., Schuschnigg, S., Holzer, C., Perko, L., Fasching, M. & Friesenbichler, W., 2013, In: Berg- und hüttenmännische Monatshefte : BHM. 158, p. 200-205

    Research output: Contribution to journal › Article › Research › peer-review

  4. Published

    Capabilities of a Demolding Force Measurement Tool for Injection Molding

    Struklec, T., Holzer, C., Lucyshyn, T., Balika, W. & Moderegger, S., 2013, Proceedings of the Asia-Australasia Conference of PPS 2013. p. 051-051

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  5. Published

    Compact Recreational Rebreather With Innovative Gas Sensing Concept and Low Work of Breathing Design

    Sieber, A., Schuster, A., Reif, S., Kessler, M., Lucyshyn, T., Buzzacott, P. & Enoksson, P., 2013, In: Marine Technology Society journal. 47, 6, p. 27-41

    Research output: Contribution to journal › Article › Research › peer-review

  6. Published

    DESIGN OF A DEMOLDING FORCE MEASUREMENT TOOL FOR INJECTION MOLDING

    Struklec, T., Burgsteiner, M., Lucyshyn, T., Balika, W., Moderegger, S. & Holzer, C., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

  7. Published

    Deformation Analysis of an Automotive Part by Injection Molding Simulation: Influence of Material Data and Mold Modeling on Prediction Quality

    Luger, H-J., Berger, G., Müller, F., Friesenbichler, W., Beytollahi, I. & Filz, P., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

  8. Published

    Deformation Analysis of an Automotive Part by Injection Molding Simulation: Influence of Material Data and Mold Modelling on Prediction Quality

    Luger, H-J., Berger, G., Müller, F., Friesenbichler, W., Beytollahi, I. & Filz, P., 2013, 29th International Conference of the Polymer Processing Society. p. 59-59

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  9. Published

    Design of a Demolding Force Measurement Tool for Injection Molding

    Struklec, T., Burgsteiner, M., Lucyshyn, T., Balika, W., Moderegger, S. & Holzer, C., 2013, Proceedings of the Polymer Processing Society 29th Annual Meeting ~ PPS-29. p. xxx-xxx

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  10. Published

    Dielectric ResidenceTime Measurements on Single Screw Extruders

    Schuschnigg, S., Reinberger, W., Holzer, C. & Fertschej, A., 2013, PPS-29 Polymer Processing Scociety. p. 31-31

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  11. Published

    Direct Regularized Surface Reconstruction from Gradients for Industrial Photometric Stereo

    Harker, M. & O'Leary, P., 2013, In: Computers in industry. p. 1-21

    Research output: Contribution to journal › Article › Research › peer-review

Previous 1...33 34 35 36 37 38 39 40 ...63 Next

Advanced filters

All authors

Reset

to
Reset filters