Investigation of parameters determining the accuracy of gas-initially-in-place calculation from well test interpretation

Research output: ThesisMaster's Thesis

Bibtex - Download

@mastersthesis{d6a7c468de4447329a8669e7cb5284ed,
title = "Investigation of parameters determining the accuracy of gas-initially-in-place calculation from well test interpretation",
abstract = "Well testing is a very important part in the evaluation of gas discoveries. It is used to define the characteristics of a reservoir, to find boundaries and see a potential pressure depletion, which could verify the existence of a limited reservoir at an early stage. This thesis evaluated the analytical test interpretation methods. An important point is the non-uniqueness of a well test interpretation. The same pressure curve can be the result of very different conditions, leading to difficulties in the interpretation. In order to find out about the exactness of the estimation of producible volumes from an early well test, data of all performed pressure build-up tests from the RAG Rohoel-Aufsuchungs AG - concession in the Molasse in Upper Austria and Salzburg is digitized, and therefore around 600 tests can be analyzed. The used method of deriving the average drainage pressure is highly controversial. The analysis of the archived data shows that in both cases, for open-hole and cased-hole tests, gas volumes are often estimated inexactly. The possibility to build numerical models of the tests is presented and evaluated. The standard well testing software can be used to model the acquired insights and to converge it interdisciplinary with the extensive knowledge of the geologist. Dynamic 2D- and 3D- simulation of the tests with a commercial simulation software allows to analyze different geologic environments and show clearly that the determination of average pressures in reservoirs with boundaries is very risky, and can lead to a severe overestimation, but also a slight underestimation of the reserves. Without a rough estimation of the lateral extension beforehand, a prediction of the proper case is not possible. Therefore, the estimation of reserves in these environments with the material balance method is erroneous. The compiled well test interpretation data and the results from the simulations are used to feed a neural network. With real-world data it is only possible to find numerical relations under certain preconditions, like the exclusion of samples with a lower production than 5 MMscm or the differentiation between formations. These reservoirs can be defined as geologically similar formations, which perform likewise during the test and during production. First trials to feed a neural network with simulation results and use this method to improve the prediction accuracy show that the capability of predicting gas initially in place strongly depends on the predefined knowledge about geological conditions. This method is, therefore, only partly applicable to real-world problems.",
keywords = "Druckaufbaumessung, Gaslagerst{\"a}tten, Lagerst{\"a}ttengrenzen, limitierte Lagerst{\"a}tte, Druckaufbaukurve, Molassezone, Open-Hole Test, Cased-Hole Test, numerischen Modellierung, Bohrlochtests, dynamische 2D- oder 3D-Simulation, neuronales Netz, well testing, gas discoveries, reservoir boundaries, limited reservoir, pressure curve, derivative curve, Molasse, open-hole tests, cased-hole tests, numerical model, dynamic 2D and 3D simulation, neural network",
author = "Gudrun Lemmerer",
note = "embargoed until 02-02-2021",
year = "2016",
language = "English",

}

RIS (suitable for import to EndNote) - Download

TY - THES

T1 - Investigation of parameters determining the accuracy of gas-initially-in-place calculation from well test interpretation

AU - Lemmerer, Gudrun

N1 - embargoed until 02-02-2021

PY - 2016

Y1 - 2016

N2 - Well testing is a very important part in the evaluation of gas discoveries. It is used to define the characteristics of a reservoir, to find boundaries and see a potential pressure depletion, which could verify the existence of a limited reservoir at an early stage. This thesis evaluated the analytical test interpretation methods. An important point is the non-uniqueness of a well test interpretation. The same pressure curve can be the result of very different conditions, leading to difficulties in the interpretation. In order to find out about the exactness of the estimation of producible volumes from an early well test, data of all performed pressure build-up tests from the RAG Rohoel-Aufsuchungs AG - concession in the Molasse in Upper Austria and Salzburg is digitized, and therefore around 600 tests can be analyzed. The used method of deriving the average drainage pressure is highly controversial. The analysis of the archived data shows that in both cases, for open-hole and cased-hole tests, gas volumes are often estimated inexactly. The possibility to build numerical models of the tests is presented and evaluated. The standard well testing software can be used to model the acquired insights and to converge it interdisciplinary with the extensive knowledge of the geologist. Dynamic 2D- and 3D- simulation of the tests with a commercial simulation software allows to analyze different geologic environments and show clearly that the determination of average pressures in reservoirs with boundaries is very risky, and can lead to a severe overestimation, but also a slight underestimation of the reserves. Without a rough estimation of the lateral extension beforehand, a prediction of the proper case is not possible. Therefore, the estimation of reserves in these environments with the material balance method is erroneous. The compiled well test interpretation data and the results from the simulations are used to feed a neural network. With real-world data it is only possible to find numerical relations under certain preconditions, like the exclusion of samples with a lower production than 5 MMscm or the differentiation between formations. These reservoirs can be defined as geologically similar formations, which perform likewise during the test and during production. First trials to feed a neural network with simulation results and use this method to improve the prediction accuracy show that the capability of predicting gas initially in place strongly depends on the predefined knowledge about geological conditions. This method is, therefore, only partly applicable to real-world problems.

AB - Well testing is a very important part in the evaluation of gas discoveries. It is used to define the characteristics of a reservoir, to find boundaries and see a potential pressure depletion, which could verify the existence of a limited reservoir at an early stage. This thesis evaluated the analytical test interpretation methods. An important point is the non-uniqueness of a well test interpretation. The same pressure curve can be the result of very different conditions, leading to difficulties in the interpretation. In order to find out about the exactness of the estimation of producible volumes from an early well test, data of all performed pressure build-up tests from the RAG Rohoel-Aufsuchungs AG - concession in the Molasse in Upper Austria and Salzburg is digitized, and therefore around 600 tests can be analyzed. The used method of deriving the average drainage pressure is highly controversial. The analysis of the archived data shows that in both cases, for open-hole and cased-hole tests, gas volumes are often estimated inexactly. The possibility to build numerical models of the tests is presented and evaluated. The standard well testing software can be used to model the acquired insights and to converge it interdisciplinary with the extensive knowledge of the geologist. Dynamic 2D- and 3D- simulation of the tests with a commercial simulation software allows to analyze different geologic environments and show clearly that the determination of average pressures in reservoirs with boundaries is very risky, and can lead to a severe overestimation, but also a slight underestimation of the reserves. Without a rough estimation of the lateral extension beforehand, a prediction of the proper case is not possible. Therefore, the estimation of reserves in these environments with the material balance method is erroneous. The compiled well test interpretation data and the results from the simulations are used to feed a neural network. With real-world data it is only possible to find numerical relations under certain preconditions, like the exclusion of samples with a lower production than 5 MMscm or the differentiation between formations. These reservoirs can be defined as geologically similar formations, which perform likewise during the test and during production. First trials to feed a neural network with simulation results and use this method to improve the prediction accuracy show that the capability of predicting gas initially in place strongly depends on the predefined knowledge about geological conditions. This method is, therefore, only partly applicable to real-world problems.

KW - Druckaufbaumessung

KW - Gaslagerstätten

KW - Lagerstättengrenzen

KW - limitierte Lagerstätte

KW - Druckaufbaukurve

KW - Molassezone

KW - Open-Hole Test

KW - Cased-Hole Test

KW - numerischen Modellierung

KW - Bohrlochtests

KW - dynamische 2D- oder 3D-Simulation

KW - neuronales Netz

KW - well testing

KW - gas discoveries

KW - reservoir boundaries

KW - limited reservoir

KW - pressure curve

KW - derivative curve

KW - Molasse

KW - open-hole tests

KW - cased-hole tests

KW - numerical model

KW - dynamic 2D and 3D simulation

KW - neural network

M3 - Master's Thesis

ER -