Walter Friesenbichler
(Former)
Research output
- 2013
- Published
Application of D-optimal design of experiments on process optimization of an automotive part
Berger, G., Luger, H-J., Friesenbichler, W., Beytollahi, I., Gierth, M. & Filz, P., 2013, THE PROCEEDINGS OF THE AUSTRIAN – SLOVENIAN POLYMER MEETING 2013. p. 106-108Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Application of deflectometry for surface inspection of high-‐glossy injection-‐molded facing parts
Macher, J., Gruber, D. P., Berger, G. & Friesenbichler, W., 2013, THE PROCEEDINGS OF THE AUSTRIAN – SLOVENIAN POLYMER MEETING 2013: ASPM 2013. Ljubljana, p. 93-95Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Ausnutzung der Scher- und Dehnerwärmung zur Heizzeitverkürzung; bei der Verarbeitung von Elastomeren
Perko, L., Friesenbichler, W. & Fasching, M., 2013, In: GAK : Gummi, Fasern, Kunststoffe. 66, p. 622-624Research output: Contribution to journal › Article › Research › peer-review
- Published
Ausnutzung der Scher- und Dehnerwärmung zur Heizzeitverkürzung; bei der Verarbeitung von Elastomeren
Perko, L., Friesenbichler, W. & Fasching, M., 2013, In: Österreichische Kunststoff-Zeitschrift. p. 252-254Research output: Contribution to journal › Article › Research › peer-review
- Published
Correlation between Rheotens Measurements and Reinforcement of Polymer Nanocomposites in the Injection Molding Compounder
Battisti, M., Duretek, I., Friesenbichler, W., Guttmann, P. & Pinter, G., 2013, 1st International Conference on Rheology and Modelling of Materials - Book of Abstracts. p. 39-39Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Deformation Analysis of an Automotive Part by Injection Molding Simulation: Influence of Material Data and Mold Modeling on Prediction Quality
Luger, H-J., Berger, G., Müller, F., Friesenbichler, W., Beytollahi, I. & Filz, P., 2013.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Deformation Analysis of an Automotive Part by Injection Molding Simulation: Influence of Material Data and Mold Modelling on Prediction Quality
Luger, H-J., Berger, G., Müller, F., Friesenbichler, W., Beytollahi, I. & Filz, P., 2013, 29th International Conference of the Polymer Processing Society. p. 59-59Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Die Wirkung dynamischer Werkzeugtemperierung auf die Oberflächenqualität von Kunststoffteilen
Pacher, G., Berger, G., Friesenbichler, W. & Gruber, D. P., 2013, 22. Leobener Kunststoff-Kolloquium: Oberlfächen und Grenzflächen in der Polymertechnologie. p. 101-110Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Elongational viscosity of rubber compounds and improving corresponding models
Perko, L., Friesenbichler, W., Obendrauf, W., Buchebner, V. & Chaloupka, G., 2013, In: Advances in production engineering & management. 8, p. 126-133Research output: Contribution to journal › Article › Research › peer-review
- Published
INFLUENCE OF PROCESS SETTINGS ON THE TOPOGRAPHY OF SINK MARKS
Pacher, G., Berger, G., Gruber, D. P. & Friesenbichler, W., 2013, ADVANCES IN PLASTICS TECHNOLOGY - Conference Papers. Gliwice, Polen, p. Paper No. 31Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
