Harald Leitner
(Former)
Research output
- Published
Refined cyclic R-curve determination through residual crack tip stress reduction by annealing
Walch, L., Klünsner, T., Ressel, G., Marsoner, S. M., Pippan, R., Hackl, A., Leitner, H. & Hohenwarter, A., 27 Jun 2024, In: International Journal of Fatigue. 187.2024, October, 108480.Research output: Contribution to journal › Article › Research › peer-review
- Published
Investigation of Cu precipitation in bcc-Fe-Comparison of numerical analysis with experiment
Warczok, P., Reith, D., Schober, M., Leitner, H., Podloucky, R. & Kozeschnik, E., 2011, In: International journal of materials research : IJMR ; Zeitschrift für Metallkunde. p. 709-716Research output: Contribution to journal › Article › Research › peer-review
- Published
The microstructure of heat-treated nickel-based superalloy 718Plus
Whitmore, L., Ahmadi, M. R., Guetaz, L., Leitner, H., Povoden-Karadeniz, E., Stockinger, M. & Kozeschnik, E., 2014, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 610, p. 39-45Research output: Contribution to journal › Article › Research › peer-review
- Published
Microstructural investigation of thermally aged nickel-based superalloy 718Plus
Whitmore, L., Ahmadi, M. R., Stockinger, M., Povoden-Karadeniz, E., Kozeschnik, E. & Leitner, H., 2014, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 594, p. 253-259Research output: Contribution to journal › Article › Research › peer-review
- Published
Transmission electron microscopy of single and double aged 718plus superalloy
Whitmore, L., Leitner, H., Povoden-Karadeniz, E., Radis, R. & Stockinger, M., 2012, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 534, p. 413-423Research output: Contribution to journal › Article › Research › peer-review
- Published
Influence of aluminium nitride on the high-temperature ductility of continuous cast slabs
Winkelhofer, F., Parteder, E., Clemens, H., Leitner, H., Spiradek-Hahn, K. & Kozeschnik, E., 2008, In: Practical metallography = Praktische Metallographie. 45, p. 159-172Research output: Contribution to journal › Article › Research › peer-review
- Published
Einfluss von Aluminiumnitrid auf die Hochtemperaturduktilität von stranggegossenen Brammen
Winkelhofer, F., Parteder, E., Leitner, H., Clemens, H., Spiradek-Hahn, K. & Kozeschnik, E., 2006, Fortschritte in der Metallographie 38. Werkstoff-Informationsges., p. 281-288Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Short-term creep behavior of a Cr Mo V hot-work tool steel
Wurmbauer, H., Leitner, H., Panzenböck, M., Scheu, C. & Clemens, H., 2009, In: International journal of materials research : IJMR ; Zeitschrift für Metallkunde. 100, p. 1066-1073Research output: Contribution to journal › Article › Research › peer-review
- Published
Kurzzeitkriechverhalten eines Warmarbeitsstahls
Wurmbauer, H., Scheu, C., Panzenböck, M., Stergar, E., Leitner, H., Clemens, H. & Caliskanoglu, Z. D., 2008, Herausforderungen neuer Werkstoffe an die Forschung und Werkstoffprüfung. p. 251-256Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Short-term Creep Behavior of an X 37 Cr Mo V 5-1 Hot-work Tool Steel with almost Bainitic and fully Martensitic Microstructures
Wurmbauer, H., Leitner, H., Panzenböck, M., Scheu, C. & Clemens, H., 2010, In: Steel research international. p. 569-575Research output: Contribution to journal › Article › Research › peer-review
