Gerald Ressel
(Former)
1 - 10 out of 16Page size: 10
Research output
- Published
Refined cyclic R-curve determination through residual crack tip stress reduction by annealing
Walch, L., Klünsner, T., Ressel, G., Marsoner, S. M., Pippan, R., Hackl, A., Leitner, H. & Hohenwarter, A., 27 Jun 2024, In: International Journal of Fatigue. 187.2024, October, 108480.Research output: Contribution to journal › Article › Research › peer-review
- Published
The evolution of Y distribution during the processing route of mechnically alloyed iron studied by means of atom probe tomography
Ressel, G., Primig, S. & Leitner, H., 2013, In: International journal of materials research : IJMR ; Zeitschrift für Metallkunde. 104, p. 1088-1095Research output: Contribution to journal › Article › Research › peer-review
- Published
Atomistic insights into milling mechanisms in an fe-Y2O3 model alloy
Ressel, G., Holec, D., Fian, A., Mendez Martin, F. & Leitner, H., 2013, In: Applied physics / A (Series A, Materials science & processing).Research output: Contribution to journal › Article › Research › peer-review
- Published
New findings on the atomistic mechanisms active during mechanical milling of a Fe-Y2O3 model alloy
Ressel, G., Parz, P., Primig, S., Leitner, H., Clemens, H. & Puff, W., 2014, In: Journal of applied physics. 115, p. 1243131-1243137Research output: Contribution to journal › Article › Research › peer-review
- Published
On the behavior of yttria/yttrium during mechanical alloying of a Fe-Y2O3 model alloy system
Ressel, G., Parz, P., Fian, A., Holec, D., Primig, S., Puff, W., Leitner, H. & Clemens, H., 2013.Research output: Contribution to conference › Poster › Research › peer-review
- Published
The effect of Zr incorporation caused by ball abrasion in a milled Fe-Y2O3 model alloy
Ressel, G., Primig, S. & Leitner, H., 2014, In: Metallurgical and materials transactions. A, Physical metallurgy and materials science . 45, p. 1552-1558Research output: Contribution to journal › Article › Research › peer-review
- Published
On the behavior of yttria/yttrium during mechanical alloying of a Fe-Y2O3 model alloy system
Ressel, G., Parz, P., Fian, A., Holec, D., Primig, S., Puff, W., Leitner, H. & Clemens, H., 2014, Advanced Materials Research. p. 598-603Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Charakterisierung von Mikrorissen in Zn-Al-Mg-Beschichtungen
Ressel, G., 2010Research output: Thesis › Diploma Thesis
- Published
New findings on the mechanisms during mechanical alloying of a Fe-Y2O3 model alloy and an oxide dispersion strengthened high-alloyed steel
Ressel, G., 2014, 155 p.Research output: Thesis › Doctoral Thesis
- Published
Microstructural refinement by spontaneous recrystallization without prior deformation of a 15-5 PH steel alloy and its mechanism
Ressel, G., Brandl, D., Hönigmann, T., Lukas, M., Stark, A., Gruber, C., Lukas, S., Stockinger, M. & Kozeschnik, E., 27 Sept 2023, In: Materials and Design. 234.2023, October, 11 p., 112370.Research output: Contribution to journal › Article › Research › peer-review
