Gerald Berger-Weber

(Former)

61 - 80 out of 135Page size: 20

Research output

  1. 2015
  2. Published

    On the Use of Interfacial Tension Parameter to Predict Reduction of Friction by Mold Coatings in Injection Molding of Polyamide 6

    Berger, G., Steffel, C. & Friesenbichler, W., 2015, p. 51. 1 p.

    Research output: Contribution to conference › Presentation › Research › peer-review

  3. Published

    On the Use of Interfacial Tension Parameter to Predict Reduction of Friction by Mold Coatings in Injection Molding of Polyamide 6

    Berger, G., Steffel, C. & Friesenbichler, W., 2015, Polymer Processing Society Graz 2015 - Book of Abstract. p. 51 1 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  4. Published

    Robust process control for rubber injection moulding with use of systematic simulations and improved material data

    Fasching, M., Berger, G., Friesenbichler, W., Filz, P. & Helbich, B., 2015, In: International Polymer Science and Technology. 42, 3, p. T1-T3

    Research output: Contribution to journal › Article › Research › peer-review

  5. 2014
  6. Published

    Robuste Prozessführung beim Kautschukspritzgießen unter Nutzung systematischer Simulation und verbesserter Materialdaten

    Fasching, M., Berger, G., Friesenbichler, W., Filz, P. & Helbich, B., Oct 2014, In: GAK : Gummi, Fasern, Kunststoffe. 10/2014, p. 640-644 5 p.

    Research output: Contribution to journal › Article › Research › peer-review

  7. Published

    Einsatz der Simulation in der systematischen Bauteilentwicklung

    Berger, G. & Friesenbichler, W., 27 Feb 2014, p. 1-38. 38 p.

    Research output: Contribution to conference › Presentation › Research › peer-review

  8. Published

    A Novel Sink Mark Model for High Gloss Injection Molded Parts - Correlation of Deflectometric and Topographic Measurements

    Macher, J., Gruber, D. P., Altenbuchner, T., Pacher, G., Berger, G. & Friesenbichler, W., 2014, In: Polymer Testing. 39, p. 12-19

    Research output: Contribution to journal › Article › Research › peer-review

  9. Published

    Detection of Visually Perceptible Sink Marks on High Gloss Injection Molded Parts by Phase Measuring Deflectometry

    Macher, J., Gruber, D. P., Altenbuchner, T., Pacher, G., Berger, G. & Friesenbichler, W., 2014, In: Polymer Testing. p. 42-48

    Research output: Contribution to journal › Article › Research › peer-review

  10. Published

    Determination of a Robust Process Setting for an Injection Molded Mirror Drive Component Using D-Optimal DoE

    Berger, G., Friesenbichler, W., Luger, H.-J., Gierth, M., Beytollahi, I. & Filz, P., 2014, 30th International Conference of the Polymer Processing Scociety: DIGITAL BOOK OF ABSTRACTS AND CONFERENCE PAPERS. p. 10-390

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  11. Published

    Evaluation of Rubber Injection Molding Simulation by Correlation of Simulated Curing Degree to Measureable Part Properties

    Fasching, M., Friesenbichler, W. & Berger, G., 2014, 30th International Conference of the Polymer Processing Scociety: DIGITAL BOOK OF ABSTRACTS AND CONFERENCE PAPERS. p. 11-349

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  12. Published

    Hochqualitative Bauteiloberflächen im Spritzguss – Möglichkeiten und Grenzen der Prozessführung

    Friesenbichler, W. & Berger, G., 2014, Tagungsband: Spritzgießen & Veredeln; Produktion funktioneller, hochwertiger Oberflächen. Deutschland: Carl Hanser Verlag GmbH & Co. KG

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  13. Published

    Influence of mold surface temperature on polymer part warpage in rapid heat cycle molding

    Berger, G. R., Pacher, G. A., Pichler, A., Friesenbichler, W. & Gruber, D. P., 2014, Proceedings of PPS 2013 - 29th International Conference of the Polymer Processing Society, Conference Papers. Vol. 1593. p. 189-194 6 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  14. Published

    Influence of Thermal Conductivity of PP-Based Compounds on Surface Roughness of Rapid Heat Cycle Injection Molded Parts

    Pacher, G., Geissler, B., Macher, J., Berger, G., Gruber, D. P. & Friesenbichler, W., 2014, 30th International Conference of the Polymer Processing Scociety: DIGITAL BOOK OF ABSTRACTS AND CONFERENCE PAPERS. p. 10-136

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  15. Published

    In-mold sensor concept to calculate process-specific rheological properties

    Pacher, G. A., Berger, G. R., Friesenbichler, W., Gruber, D. P. & Macher, J., 2014, In: AIP Conference Proceedings. 1593, p. 179-182

    Research output: Contribution to journal › Article › Research › peer-review

  16. Published

    Measurement of the visual perceptibility of sink marks on injection molding parts by a new fast processing model

    Gruber, D. P., Macher, J., Haba, D., Berger, G., Pacher, G. & Friesenbichler, W., 2014, In: Polymer Testing. 33, p. 7-12

    Research output: Contribution to journal › Article › Research › peer-review

  17. Published

    Prediction of friction in injection molding by wetting parameters?

    Berger, G., Friesenbichler, W., Steffel, C. & Pacher, G., 2014, 6th International PMI Conference Proceedings. p. 61-66

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  18. Published

    Rapid Heat Cycle Molding, Surface Topography and Visual Appearance of Injection Molded Parts. Research Work in Leoben in the Last 10 Years.

    Berger, G., Friesenbichler, W., Gruber, D. P., Pacher, G. & Macher, J., 2014, ANTEC® 2014 - Proceedings of the Technical Conference & Exhibition. Brown, H. L. & Jones, D. H. (eds.). p. 1700-1705

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  19. Published

    Sink mark shape dependin on holdin pressure and rapid heat c clemoldin -mathematical approimation and KE parameters

    Pacher, G. A., Gruber, D. P., Rescher, M., Berger, G. R. & Friesenbichler, W., 2014, 72nd Annual Technical Conference of the Society of Plastics Engineers, ANTEC 2014: The Plastics Conference. January ed. Vol. 2. p. 1716-1720 5 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  20. 2013
  21. Published

    A novel method for the characterization of surface defects remarkably close to the human perception

    Gruber, D. P., Pacher, G., Macher, J., Berger, G. & Friesenbichler, W., 2013, 29th International Conference of the Polymer Processing Society. p. 48-48

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  22. Published

    AN OVERVIEW ON RESEARCH WORK IN LEOBEN IN THE FIELDS OF RAPID HEAT CYCLE MOLDING, SURFACE TOPOGRAPHY AND VISUAL APPEARANCE OF INJECTION MOLDED PARTS

    Pacher, G., Berger, G., Gruber, D. P. & Friesenbichler, W., 2013, ADVANCES IN PLASTICS TECHNOLOGY - Conference Papers. p. Paper No. 27

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  23. Published

    Application of deflectometry for surface inspection of high-­‐glossy injection-­‐molded facing parts

    Macher, J., Gruber, D. P., Berger, G. & Friesenbichler, W., 2013, THE PROCEEDINGS OF THE AUSTRIAN – SLOVENIAN POLYMER MEETING 2013: ASPM 2013. Ljubljana, p. 93-95

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

Previous 1 2 3 4 5 6 7 Next
View graph of relations

Latest Research Output

View more (135)