Georg Felix Geier

(Former)

Research output

  1. 2011
  2. Published

    Computertomografische Untersuchung von Stahlfaserspritzbeton mit mehrdimensionalen Transferfunktionen

    Pittino, G., Geier, G., Fritz, L., Hadwiger, M., Rosc, J. & Pabel, T., 2011, In: Beton- und Stahlbetonbau. p. 364-370

    Research output: Contribution to journalArticleResearchpeer-review

  3. Published

    Correlation of porosity detected by computed tomography and fatigue strength of aluminium alloys

    Pabel, T., Geier, G., Habe, D., Rosc, J., Petkov, T. & Schumacher, P., 2011.

    Research output: Contribution to conferencePosterResearchpeer-review

  4. Published

    Correlation of porosity detected by computed tomography and fatigue strength of aluminium alloys

    Pabel, T., Geier, G., Habe, D., Rosc, J., Schumacher, P. & Petkov, T., 2011, TMS Conference-Supplemental Proceedings, General Paper Selections. p. 803-805

    Research output: Chapter in Book/Report/Conference proceedingConference contribution

  5. Published

    Correlation of porosity detected by computed tomography and fatigue strength of aluminium alloys

    Pabel, T., Geier, G., Habe, D., Rosc, J., Schumacher, P. & Petkov, T., 2011.

    Research output: Contribution to conferencePosterResearchpeer-review

  6. Published

    Neue Wege in der Computertomographie und der Bauteilprüfung

    Rosc, J., Pabel, T., Geier, G., Habe, D. & Brunke, O., 2011, In: Gießerei-Rundschau. p. 98-101

    Research output: Contribution to journalArticleResearchpeer-review

  7. 2010
  8. Published

    Analysis and Exploration of CT-Data using application specific Multi-Dimensional Transfer Functions

    Geier, G., Fritz, L., Hadwiger, M., Rosc, J., Pabel, T., Habe, D., Pittino, G. & Schumacher, P., 2010, Analysis and Exploration of CT-Data using application specific Multi-Dimensional Transfer Functions. p. 1-13

    Research output: Chapter in Book/Report/Conference proceedingConference contribution

  9. Published

    Charakterisierung der Schmelzequalität einer AlSi7Mg0,5(Cu,Fe)-Legierung (Typ LM25)

    Haberl, K., Schumacher, P., Geier, G. F. & Stauder, B., 2010, In: Gießerei-Rundschau. 58, 7/8, p. 131-136

    Research output: Contribution to journalArticleResearchpeer-review

  10. Published

    Computertomographie

    Wenzl, B., Schumacher, P. & Geier, G., 2010.

    Research output: Contribution to conferencePosterResearchpeer-review

  11. Published

    Computertomographie als zerstörungsfreies Prüfverfahren für Gussteile

    Geier, G., Pabel, T., Habe, D., Rosc, J., Hadwiger, M., Höllt, T. & Fritz, L., 2010, In: Druckguss-Praxis. p. 171-174

    Research output: Contribution to journalArticleResearchpeer-review

  12. Published

    Correlation of Porosity Detected by Computed Tomography and Fatigue Strength of Aluminium Alloys

    Pabel, T., Geier, G., Habe, D., Rosc, J., Schumacher, P. & Petkov, T., 2010, Correlation of Porosity Detected by Computed Tomography and Fatigue Strength of Aluminium Alloys. p. 1-2

    Research output: Chapter in Book/Report/Conference proceedingConference contribution

Previous 1 2 3 4 5 6 7 Next