Departments and Chairs

Organisational unit: Departments and Institutes

33401 - 33410 out of 33,496Page size: 10

Research output

  1. Published

    Modelling Al-4wt.%Cu as-cast structure using equiaxed morphological parameters deduced from in-situ synchrotron X-ray radiography

    Ahmadein, M., Wu, M., Reinhart, G. & Nguyen-Thi, H., 2016, In: IOP Conference Series: Materials Science and Engineering.

    Research output: Contribution to journal › Article › Research › peer-review

  2. Published

    Evaluation of a 5-phase mixed columnar-equiaxed solidification model with a benchmark solidification experiment of NH4Cl-H2O solution

    Ahmadein, M., Wu, M., Stefan Kharicha, M., Kharicha, A. & Ludwig, A., 2014, Materials Science Forum. Vol. 790-791.2013. p. 247-252 6 p. (Materials Science Forum).

    Research output: Chapter in Book/Report/Conference proceeding › Chapter › Research

  3. Published

    A numerical study of the influence of pouring technique on the as-cast structure of Al-Cu ingots

    Ahmadein, M., Wu, M., Schumacher, P. & Ludwig, A., 2014, Materials Science Forum. Vol. 790-791.2014. p. 67-72 (Materials Science Forum).

    Research output: Chapter in Book/Report/Conference proceeding › Chapter › Research

  4. Published

    Analysis of well-known reservoir models and sensitivity of different parameters to estimate deliverability from vertical, horizontal and fracked gas wells

    Ahmad, H., 2016

    Research output: Thesis › Master's Thesis

  5. Published

    Investigation of Material Property Model on Substrate Deformation Induced by Thick-Walled WAAM Process Using Numerical Computation

    Ahmad, S. N., Manurung, Y. H. P., Mat, M. F. & Leitner, M., 2021, Recent Trends in Manufacturing and Materials Towards Industry 4.0 - Selected Articles from iM3F 2020, Malaysia. Osman Zahid, M. N., Abdul Sani, A. S., Mohamad Yasin, M. R., Ismail, Z., Che Lah, N. A. & Mohd Turan, F. (eds.). p. 747-761 15 p. (Lecture Notes in Mechanical Engineering; vol. 46).

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  6. Published

    Numerical Simulation on Residual Stress and Substrate Deformation of Bead-On-Plate of SS316L Using Inherent Strain Method

    Ahmad, S. N., Manurung, Y. H. P., Taufek, T. & Leitner, M., 2021, Recent Trends in Manufacturing and Materials Towards Industry 4.0 - Selected Articles from iM3F 2020, Malaysia. Osman Zahid, M. N., Abdul Sani, A. S., Mohamad Yasin, M. R., Ismail, Z., Che Lah, N. A. & Mohd Turan, F. (eds.). p. 723-738 16 p. (Lecture Notes in Mechanical Engineering; vol. 46).

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  7. Published

    Inducing micro-cracks improves the recovery in heap leaching operations

    Ahlqvist, N.-P. J., 2016

    Research output: Thesis › Master's Thesis (University Course)

  8. Published

    ENVIRONMENTAL LIFE CYCLE ASSESSMENT

    Ahlman, T., 2010

    Research output: Thesis › Master's Thesis (University Course)

  9. Published

    Regional Distribution of Magnetic susceptibilities and 3 D Modelling of Aeromagnetik anomalies in the Central Eastern alps (Western Tauern Window), Austria.

    Ahl, A., Slapansky, P., Belocky, R., Piber, A., Seiberl, W., Zechner, M. & Mauritsch, H. J., 2007, In: Austrian journal of earth sciences. 100, p. 138-151

    Research output: Contribution to journal › Article › Research › peer-review

  10. Published

    Droplet phase change phenomena in CFD simulations of wet scrubbers and quenching processes

    Aguayo Arellano, P. I., 2005

    Research output: Thesis › Doctoral Thesis

Previous 1...3337 3338 3339 3340 3341 3342 3343 3344 ...3350 Next
View graph of relations