Department Product Engineering
Organisational unit: Departments and Institutes
751 - 760 out of 3,156Page size: 10
Research output
- 2017
- Published
Impact of Axial Component Alignment in Total Knee Arthroplasty on Lower Limb Rotational Alignment: An in Vitro Study
Maderbacher, G., Baier, C., Springorum, H. R., Maderbacher, H., Birkenbach, A. M., Benditz, A., Grifka, J. & Keshmiri, A., 1 May 2017, In: Journal of Knee Surgery. 30.2017, 4, p. 372-377 6 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Technical Report - Finite Element Analysis - 3" Clamp Connector Rev. 1
Hopp, S., Kessler, F., Prenner, M., Stojkovic, S., Pramstaller, M. & Fimbinger, E., May 2017, 104 p.Research output: Book/Report › Commissioned report › Research
- Published
Technical Report - Finite Element Analysis - 3" Clamp Connector Rev. 2
Hopp, S., Kessler, F., Prenner, M., Stojkovic, S., Pramstaller, M. & Fimbinger, E., May 2017, 100 p.Research output: Book/Report › Commissioned report › Research
- Published
Auslegung konturnaher Kühlsysteme für Spritzgießwerkzeuge. Vergleich von SLM-gedruckten mit hochwärmeleitfähigen konventionellen Formeinsätzen
Berger, G., Zorn, D., Panzl, G. & Bevc, F., 21 Apr 2017, p. 229-243. 15 p.Research output: Contribution to conference › Presentation › Research › peer-review
- Published
Spritzgusssimulation als Basis optimierter Bauteile
Primetzhofer, A., Stadler, G. & Pinter, G. G., 20 Apr 2017.Research output: Contribution to conference › Paper
- Published
Spritzgusssimulation als Basis optimierter Bauteile
Primetzhofer, A., Stadler, G. & Pinter, G. G., 20 Apr 2017.Research output: Contribution to conference › Poster › Research
- Published
Residual stress state induced by high frequency mechanical impact treatment in different steel grades – Numerical and experimental study
Khurshid, M., Leitner, M., Barsoum, Z. & Schneider, C., 1 Apr 2017, In: International Journal of Mechanical Sciences. 123.2017, April, p. 34-42 9 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Auslegung konturnaher Kühlsysteme für Spritzgießwerkzeuge. Vergleich von SLM-gedruckten mit hochwärmeleitfähigen konventionellen Formeinsätzen
Berger, G., Zorn, D., Panzl, G. & Bevc, F., Apr 2017, 26. Leobener Kunststoff-Kolloquium 20. und 21. April 2017: Schriftenreihe Kunststofftechnik. Friesenbichler, W. & Berger, G. (eds.). Leoben, Vol. 7. p. 229-243 15 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Laser Powder Bed Fusion – Materials Issues and Optimized Processing Parameters for Tool steels, AlSiMg- and CuCrZr-Alloys
Buchmayr, B., Panzl, G., Walzl, A. & Wallis, C., Apr 2017, In: Advanced engineering materials. 19.2017, 4, 11 p., 1600667.Research output: Contribution to journal › Article › Research › peer-review
- Published
Technical Report - Finite Element Analysis - 1" Clamp Connector Rev. 3
Hopp, S., Kessler, F., Prenner, M., Stojkovic, S., Pramstaller, M. & Fimbinger, E., Apr 2017, 104 p.Research output: Book/Report › Commissioned report › Research
