Department Polymer Engineering and Science
Organisational unit: Departments and Institutes
481 - 490 out of 4,193Page size: 10
Research output
- Published
Improved cure simulation in pultrusion process about heating systems: A case study
Costa Dias, R. D. C., Santos, L. S. & Schledjewski, R., 26 Jun 2016, Proceedings of the 17th European Conference on Composite Materials (ECCM17).Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Improving degree of cure in pultrusion process by optimizing die-temperature
Costa Dias, R. D. C., Santos, L. D. S., Ouzia, H. & Schledjewski, R., 1 Dec 2018, In: Materials Today Communications. 17.2018, December, p. 362-370 9 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Comparative study of optimization in pultrusion with pre-heating and die-cooler temperature for improved cure
Costa Dias, R. D. C., de Sousa Santos, L. & Schledjewski, R., 1 Jan 2017, THERMEC 2016. Ionescu, M., Mishra, B., Kozeschnik, E., Sommitsch, C., Chandra, T. & Mishra, B. (eds.). Trans Tech Publications, p. 402-407 6 p. (Materials Science Forum; vol. 879).Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Kinetic parameter estimation and simulation of pultrusion process of an epoxy-glass fiber system
Costa Dias, R. D. C., Leali Costa, M., Santos, L. D. S. & Schledjewski, R., 22 Jun 2020, In: Thermochimica Acta. 690.2020, August, 12 p., 178636.Research output: Contribution to journal › Article › Research › peer-review
- Published
Pultrusion of thermoset based profiles-state of the art regarding materials, process set-ups, process modeling, and process simulation
Costa Dias, R. D. C., 2020Research output: Thesis › Doctoral Thesis
- Published
Simulation der Spritzgießprozesses von Mikrobauteilen
Cramer, A., Michaeli, W., Friesenbichler, W. & Duretek, I., 2007, In: Zeitschrift Kunststofftechnik : Journal of plastics technology. 3, p. 1-26Research output: Contribution to journal › Article › Research › peer-review
- Published
Simulation des spritzgießprozesses von mikrobauteilen
Cramer, A., Michaeli, W., Friesenbichler, W. & Duretek, I., 1 Jan 2007, In: Zeitschrift Kunststofftechnik = Journal of plastics technology. 1Research output: Contribution to journal › Article › Research › peer-review
- Published
Current challenges in NdFeB permanent magnets manufacturing by Powder Injection Molding (PIM): A review
Crozier-Bioud, T., Momeni, V., Gonzalez-Gutierrez, J., Kukla, C., Luca, S. & Rolere, S., May 2023, In: Materials today. Physics. 34.2023, May, 13 p., 101082.Research output: Contribution to journal › Review article › peer-review
- Published
Einfluss der Grenzflächeneigenschaften auf die mechanischen Eigenschaften von kurzfaserverstärkten Verbunden
Cwioro, T., 2022Research output: Thesis › Master's Thesis
- Published
Identifizierung von Geruchsstoffen in Schweinestall-Luft
Czerny, M., Schieberle, P., Maier, B., Rieß, G., Gronauer, A. & Schön, H., 2001, In: Landtechnik. 56, p. 342-343Research output: Contribution to journal › Article › Research › peer-review
