Chair of Polymer Processing (350)

Organisational unit: Chair

661 - 680 out of 946Page size: 20

Research output

  1. 2011
  2. Published

    Elongational and shear flow in polymer-clay nanocomposites measured by on-line extensional and off-line shear rheometry

    Kracalik, M., Laske, S., Witschnigg, A. & Holzer, C., 2011, In: Rheologica acta. 50, p. 937-944

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    Extensional Rheology as Effective Tool for Characterization of Polymer Nanocomposites

    Kracalik, M., Laske, S. & Holzer, C., 2011, Novel Trends in Rheology IV - AIP Conference Proceedings. p. 208-218

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  4. Published

    Fundamental modelling of the expansion injection moulding with its simulation and the material degradation analyses on the moulded parts

    Rajganesh Jegadeesan, X., 2011

    Research output: Thesis › Doctoral Thesis

  5. Published

    Herstellung medienführender Leitungen durch Kombination von Coinjektion und Wasserinjektionstechnik

    Stückler, S., 2011

    Research output: Thesis › Master's Thesis

  6. Published

    Homogenitätsanalyse von Feststoffmischungen

    Eberhard, D., 2011

    Research output: Thesis › Master's Thesis

  7. Published

    Influence of induced shear energy and residence time on material properties of polypropylene nanocomposites

    Witschnigg, A., Laske, S., Duretek, I. & Holzer, C., 2011,

    Program & Abstracts of 27th Annual Meeting of the Polymer Processing Society

    .     p. 150-151

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  8. Published

    Influence of processing conditions and induced shear work on the thermal, rheological and mechanical behavior of polymer nanocomposites

    Mattausch, H., Laske, S., Duretek, I., Witschnigg, A. & Holzer, C., 2011,

    Program & Abstracts of 27th Annual Meeting of the Polymer Processing Society

    .     p. 157-158

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  9. Published

    Influence of shear energy on the properties of polyolefin nanocomposite pipes: Plastics Research Online, Reihentitel: 10.1002/spepro.003977

    Witschnigg, A., Laske, S., Kracalik, M. & Holzer, C., 2011

    Research output: Non-textual form › Web publication/site › Transfer

  10. Published

    Influence of the degree of exfoliation on the thermal conductivity of polypropylene nanocomposites

    Laske, S., Duretek, I., Witschnigg, A. & Holzer, C., 2011,

    Program & Abstracts of 27th Annual Meeting of the Polymer Processing Society

    .     p. 155-155

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  11. Published

    Influence of the heat transfer coefficient on the injection molding simulation of microstructures

    Müller, F., Lucyshyn, T., Kukla, C. & Holzer, C., 2011, Conference Proceedings - ICIT & MPT 2011 . p. 141-148

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  12. Published

    Investigations of adhesion on two-shot moulded parts

    Kisslinger, T., Lucyshyn, T., Doler, M., Langecker, G. & Holzer, C., 2011.

    Research output: Contribution to conference › Poster › Research › peer-review

  13. Published

    Kunststoffverarbeitung-Vom Rohstoff zum fertigen Bauteil

    Piontek, M., Holzer, C. & Laske, S., 2011.

    Research output: Contribution to conference › Poster › Research › peer-review

  14. Published

    Local structure around nano-clay agglomerates in PP composites – a scanning X-Ray diffraction study with sub micron resolution

    Feuchter, M., Maier, G. A., Burghammer, M., Kracalik, M., Laske, S., Keckes, J. & Pinter, G., 2011, European Polymer Congress 2011. p. 515-515

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  15. Published

    Measurement of the visual perceptibility of sink marks in injection molded parts

    Haba, D., 2011, 79 p.

    Research output: Thesis › Master's Thesis

  16. Published

    Measuring the pressure dependent viscosity at high shear rates using a new rheological injection mould

    Friesenbichler, W., Duretek, I., Rajganesh Jegadeesan, X. & Selvasankar, R. K., 2011, In: Polimery/Polymers. 56, 1, p. 58-62

    Research output: Contribution to journal › Article › Research › peer-review

  17. Published

    Mischteilberechnungen mittels FEM

    Kienzl, W., 2011, 113 p.

    Research output: Thesis › Master's Thesis

  18. Published

    Nanostructured polymer surfaces to optimize cell behaviour

    Holzer, C., Laske, S., Katschnig, M. & Balika, W., 2011.

    Research output: Contribution to conference › Poster › Research › peer-review

  19. Published

    Nanostructured polymer surfaces to optimize cell behaviour

    Holzer, C., Katschnig, M., Kracalik, M., Andraschek, N., Laske, S., Schäfer, U. & Balika, W., 2011, Abstract Book. p. 72-72

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  20. Published

    Near infrared spectroscopy - a smart way of characterization and quality control of PP-NC

    Witschnigg, A., Laske, S., Holzer, C., Patel, R., Khan, A., Benkreira, H. & Coates, P., 2011, Enhanced Polymer Processing. p. 266-284

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  21. Published

    Numerical modelling of flow in conical co-rotating twin screw extruder

    Selvasankar, R. K., Schuschnigg, S., Fertschej, A. & Holzer, C., 2011.

    Research output: Contribution to conference › Poster › Research › peer-review

Previous 1...30 31 32 33 34 35 36 37 ...48 Next
View graph of relations

Contact information

Otto Glöckel-Straße 2/III, 8700 Leoben
  • Main phone number: +43 3842 402 3501