Chair of Polymer Processing (350)
Organisational unit: Chair
881 - 890 out of 946Page size: 10
Research output
- Published
Modification of Interfacial Interactions in Ceramic-Polymer Nanocomposites by Grafting: Morphology and Properties for Powder Injection Molding and Additive Manufacturing
Cano Cano, S., Gooneie, A., Kukla, C., Rieß, G., Holzer, C. & Gonzalez-Gutierrez, J., 21 Feb 2020, In: Applied Sciences : open access journal. 10.2020, 4, 18 p., 1471.Research output: Contribution to journal › Article › Research › peer-review
- Published
Influence of the Infill Orientation on the Properties of Zirconia Parts Produced by Fused Filament Fabrication
Cano Cano, S., Lube, T., Huber, P., Gallego, A., Naranjo, J. A., Berges, C., Schuschnigg, S., Herranz, G., Kukla, C., Holzer, C. & Gonzalez-Gutierrez, J., 15 Jul 2020, In: Materials. 13.2020, 14, 19 p., 3158.Research output: Contribution to journal › Article › Research › peer-review
- Published
Development of Ceramic Feedstocks for Fused Filament Fabrication
Cano Cano, S., 2020Research output: Thesis › Doctoral Thesis
- Published
Material extrusion additive manufacturing of multi-material components
Cano Cano, S., Valy, L., Liu, D., Maurer, P., Ma, N., Czernilofsky, F., Schuschnigg, S., Sui, G., Kitzmantel, M., Kukla, C. & Gonzalez-Gutierrez, J., 15 Sept 2021, 29th Leoben-Conference on Polymer Engineering & Science. p. 184 1 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Isotropic NdFeB hard magnets: MIM production using recycled powders with and without Nd additions
Burkhardt, C., Weber, O., Podmiljsak, B., Gonzalez-Gutierrez, J., Kukla, C., Degri, M., Harris, I. R. & Walton, A., 1 Dec 2017, In: Powder injection moulding international. 11, 4, p. 75-81 7 p.Research output: Contribution to journal › Article › Research
- Published
Influencing Parameters on the Master Casting Process used for the Replication of Microstructures on Curved Surfaces via Injection Molding
Burgsteiner, M., 2013, Books of Abstracts of the 12th International Conference on NNT 2013. p. 184-184Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Investigation of the Influence of Different Coatings on the Filling Behavior and Replication Quality of Microstructures in Injection Molding
Burgsteiner, M., Müller, F., Lucyshyn, T., Kukla, C., Holzer, C., Gruber, D. P., Macher, J. & Pacher, G., 2014, Proceedings of PPS 30. p. 1-1Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Influencing Parameters on the Master Casting Process used for the Replication of Microstructures on Curved Surfaces via Injection Molding
Burgsteiner, M., 2013.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Influence of the process parameters on the replication of microstructured freeform surfaces
Burgsteiner, M., Müller, F., Lucyshyn, T., Kukla, C. & Holzer, C., 2014, AIP Conference Proceedings: PROCEEDINGS OF PPS-29: The 29th International Conference of the Polymer Processing Society - Conference Papers. Nuremberg, Germany, Vol. 1593. p. 183-188Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Entformungskräfte beim Spritzgießen in Abhängigkeit von Oberflächenrauigkeit, Stahlwerkstoff, Vorzugsrichtung der Oberflächenstruktur, Beschichtung und Kunststofftyp
Burgsteiner, M., 2009, 237 p.Research output: Thesis › Master's Thesis
