Chair of Polymer Processing (350)
Organisational unit: Chair
Research output
- Published
Modification of Interfacial Interactions in Ceramic-Polymer Nanocomposites by Grafting: Morphology and Properties for Powder Injection Molding and Additive Manufacturing
Cano Cano, S., Gooneie, A., Kukla, C., Rieß, G., Holzer, C. & Gonzalez-Gutierrez, J., 21 Feb 2020, In: Applied Sciences : open access journal. 10.2020, 4, 18 p., 1471.Research output: Contribution to journal › Article › Research › peer-review
- Published
Influence of the Infill Orientation on the Properties of Zirconia Parts Produced by Fused Filament Fabrication
Cano Cano, S., Lube, T., Huber, P., Gallego, A., Naranjo, J. A., Berges, C., Schuschnigg, S., Herranz, G., Kukla, C., Holzer, C. & Gonzalez-Gutierrez, J., 15 Jul 2020, In: Materials. 13.2020, 14, 19 p., 3158.Research output: Contribution to journal › Article › Research › peer-review
- Published
Development of Ceramic Feedstocks for Fused Filament Fabrication
Cano Cano, S., 2020Research output: Thesis › Doctoral Thesis
- Published
Material extrusion additive manufacturing of multi-material components
Cano Cano, S., Valy, L., Liu, D., Maurer, P., Ma, N., Czernilofsky, F., Schuschnigg, S., Sui, G., Kitzmantel, M., Kukla, C. & Gonzalez-Gutierrez, J., 15 Sept 2021, 29th Leoben-Conference on Polymer Engineering & Science. p. 184 1 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Isotropic NdFeB hard magnets: MIM production using recycled powders with and without Nd additions
Burkhardt, C., Weber, O., Podmiljsak, B., Gonzalez-Gutierrez, J., Kukla, C., Degri, M., Harris, I. R. & Walton, A., 1 Dec 2017, In: Powder injection moulding international. 11, 4, p. 75-81 7 p.Research output: Contribution to journal › Article › Research
- Published
Influencing Parameters on the Master Casting Process used for the Replication of Microstructures on Curved Surfaces via Injection Molding
Burgsteiner, M., 2013, Books of Abstracts of the 12th International Conference on NNT 2013. p. 184-184Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Replication of a draw-polished cavity surface into PP and PC. Influence of flow length, wall thickness and injection molding parameters
Burgsteiner, M., Berger, G. & Friesenbichler, W., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Investigation of the Influence of Different Coatings on the Filling Behavior and Replication Quality of Microstructures in Injection Molding
Burgsteiner, M., Müller, F., Lucyshyn, T., Kukla, C., Holzer, C., Gruber, D. P., Macher, J. & Pacher, G., 2014, Proceedings of PPS 30. p. 1-1Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Influencing Parameters on the Master Casting Process used for the Replication of Microstructures on Curved Surfaces via Injection Molding
Burgsteiner, M., 2013.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Replication of a draw-polished cavity surface into PP and PC. Influence of flow length, wall thickness and injection molding parameters
Burgsteiner, M., Berger, G. & Friesenbichler, W., 2009.Research output: Contribution to conference › Poster › Research › peer-review
