Chair of Polymer Processing (350)
Organisational unit: Chair
721 - 730 out of 946Page size: 10
Research output
- Published
Influence of cavity pressure and injection rate on the surface roughness of PP, PC, ABS and ABS-PC
Pacher, G., Berger, G. & Friesenbichler, W., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
On the evaluation of the visual impact of sink marks of injection molded parts
Pacher, G. A., 2009Research output: Thesis › Master's Thesis
- Published
Supportless lattice structure of 316L stainless steel fabricated by material extrusion additive manufacturing: Effect of relative density on physical, microstructural and mechanical behaviour
Parsompech, N., Suwanpreecha, C., Noraphaiphipaksa, N., Hararak, B., Songkuea, S., Schuschnigg, S., Kukla, C., Kanchanomai, C. & Manonukul, A., 14 Sept 2024, In: Materials Science and Engineering: A. 915.2024, November, 14 p., 147270.Research output: Contribution to journal › Article › Research › peer-review
- Published
Compoundierung von Filamenten für medizinische FFF-Anwendungen
Payr, B., 2016Research output: Thesis › Master's Thesis
- Published
Functionally graded additive manufacturing
Pei, E., Rumana Kabir, I., Godec, D., Gonzalez-Gutierrez, J. & Nordin, A., 9 Apr 2021, Additive Manufacturing with Functionalized Nanomaterials: Micro and Nono Technologies. Amsterdam, Neterlands: Elsevier, p. 35-54 20 p.Research output: Chapter in Book/Report/Conference proceeding › Chapter › Research
- Published
Heizzeitverkürzung für den Elastomerspritzguss mittels eines Heiz-Scher-Mischteiles
Perko, L., 2009Research output: Thesis › Master's Thesis
- E-pub ahead of print
Impact Optimization of 3D‐Printed Poly(methyl methacrylate) for Cranial Implants
Petersmann, S., Spoerk, M., Huber, P., Lang, M., Pinter, G. & Arbeiter, F., 30 Aug 2019, (E-pub ahead of print) In: Macromolecular materials and engineering. 304.2019, 11, 10 p., 1900263.Research output: Contribution to journal › Article › Research › peer-review
- Published
Mechanical Characterization of PMMA Produced by Fused Filament Fabrication as a Potential Material for Cranial Bone Reconstruction
Petersmann, S., Spörk, M., Lang, M. C., Moser, C., Pinter, G. G. & Arbeiter, F., 2019, Abstract Book of the First European Conference on Structural Integrity of Additively Manufactured Materials. 5 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Mechanical properties of polymeric implant materials produced by extrusion-based additive manufacturing
Petersmann, S., Spörk, M., Van De Steene, W., Üçal, M., Wiener, J., Pinter, G. G. & Arbeiter, F., 1 Apr 2020, In: Journal of the Mechanical Behavior of Biomedical Materials. 104.2020, April, 13 p., 103611.Research output: Contribution to journal › Article › Research › peer-review
- Accepted/In press
Structural integrity of shrinkage and warpage optimized polypropylene produced by material extrusion-based additive manufacturing
Petersmann, S., Spörk, M., Wiener, J., Pinter, G. G. & Arbeiter, F., 2020, (Accepted/In press).Research output: Contribution to conference › Abstract › peer-review
