Polymer Testing, ‎0142-9418

Journal

ISSNs0142-9418
31 - 40 out of 51Page size: 10

Research output

  1. 2015
  2. Published

    Cyclic tests on cracked round bars as a quick tool to assess the long term behaviour of thermoplastics and elastomers

    Arbeiter, F., Schrittesser, B., Frank, A., Berer, M. & Pinter, G., 3 Jun 2015, In: Polymer Testing. 45, p. 83-92 10 p., 4441.

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    Method to characterize the damping behavior of thin passively constrained layer laminates using dynamic mechanical analysis (DMA) in shear mode

    Knapp, G., Oreski, G. & Pinter, G., 2015, In: Polymer Testing. 42, p. 215 224 p.

    Research output: Contribution to journal › Article › Research › peer-review

  4. Published

    Thermal expansion behavior of solar cell encapsulation materials

    Knausz, M., Oreski, G., Schmidt, M., Guttmann, P., Berger, K. A., Voronko, Y., Eder, G., Koch, T. & Pinter, G., 2015, In: Polymer Testing. 44, p. 160-167

    Research output: Contribution to journal › Article › Research › peer-review

  5. 2014
  6. Published

    A Novel Sink Mark Model for High Gloss Injection Molded Parts - Correlation of Deflectometric and Topographic Measurements

    Macher, J., Gruber, D. P., Altenbuchner, T., Pacher, G., Berger, G. & Friesenbichler, W., 2014, In: Polymer Testing. 39, p. 12-19

    Research output: Contribution to journal › Article › Research › peer-review

  7. Published

    Characterisation of quasi-brittle fatigue crack growth in pipe grade polypropylene block copolymer

    Arbeiter, F., Pinter, G. & Frank, A., 2014, In: Polymer Testing. 37, p. 186-192

    Research output: Contribution to journal › Article › Research › peer-review

  8. Published

    Detection of Visually Perceptible Sink Marks on High Gloss Injection Molded Parts by Phase Measuring Deflectometry

    Macher, J., Gruber, D. P., Altenbuchner, T., Pacher, G., Berger, G. & Friesenbichler, W., 2014, In: Polymer Testing. p. 42-48

    Research output: Contribution to journal › Article › Research › peer-review

  9. Published

    Determination of slow crack growth behaviour of polyethylene pressure pipes with cracked round bar test

    Kratochvilla, T., Andreas, F. & Pinter, G., 2014, In: Polymer Testing. 40, p. 299-303

    Research output: Contribution to journal › Article › Research › peer-review

  10. Published

    Evaluation of the applicability of the cracked round bar test as standardized PE-pipe ranking tool

    Frank, A. & Pinter, G., 2014, In: Polymer Testing. 38, p. 161-171

    Research output: Contribution to journal › Article › Research › peer-review

  11. Published

    Measurement of the visual perceptibility of sink marks on injection molding parts by a new fast processing model

    Gruber, D. P., Macher, J., Haba, D., Berger, G., Pacher, G. & Friesenbichler, W., 2014, In: Polymer Testing. 33, p. 7-12

    Research output: Contribution to journal › Article › Research › peer-review

  12. Published

    On the strain measurement and stiffness calculation of carbon fibre reinforced composites under quasi-static tensile and tension-tension fatigue loads

    Brunbauer, J. & Pinter, G., 2014, In: Polymer Testing. 40, p. 256-264

    Research output: Contribution to journal › Article › Research › peer-review

Previous 1 2 3 4 5 6 Next
View graph of relations