Materials science and engineering: A, Structural materials: properties, microstructure and processing, ‎0921-5093

Journal

ISSNs0921-5093
Additional searchable ISSN (electronic)1873-4936
91 - 100 out of 179Page size: 10

Research output

  1. 2014

  2. Microstructure and temperature dependence of intergranular strains on diffractometric macroscopic residual stress analysis

    Wimpory, R., Krempaszky, C. & Stockinger, M., 16 Sept 2014, In: Materials Science and Engineering A. 618, p. 271-279 9 p.

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    Yield strength prediction in Ni-base alloy 718Plus based on thermo-kinetic precipitation simulation

    Ahmadi, M. R., Povoden-Karadeniz, E., Whitmore, L., Stockinger, M., Falahati, A. & Kozeschnik, E., 1 Jul 2014, In: Materials Science and Engineering A. 608, p. 114-122 9 p.

    Research output: Contribution to journal › Article › Research › peer-review

  4. Published

    Comparison of microstructural crack paths between hypo-eutectic Al-Si-Cu and Al-Si-Mg cast alloys in high plasticity regimes under rotating bending

    Huter, P., Winter, G., Renhart, P., Schwab, M., Oberfrank, S., Grün, F. & Stauder, B., 2014, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 618, p. 578-585

    Research output: Contribution to journal › Article › Research › peer-review

  5. Published

    Hot-working behavior of an advanced intermetallic multi-phase gamma-TiAl based alloy

    Schwaighofer, E., Clemens, H., Lindemann, J., Stark, A. & Mayer, S., 2014, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 614, p. 297-310

    Research output: Contribution to journal › Article › Research › peer-review

  6. Published

    Microstructural investigation of thermally aged nickel-based superalloy 718Plus

    Whitmore, L., Ahmadi, M. R., Stockinger, M., Povoden-Karadeniz, E., Kozeschnik, E. & Leitner, H., 2014, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 594, p. 253-259

    Research output: Contribution to journal › Article › Research › peer-review

  7. Published

    The microstructure of heat-treated nickel-based superalloy 718Plus

    Whitmore, L., Ahmadi, M. R., Guetaz, L., Leitner, H., Povoden-Karadeniz, E., Stockinger, M. & Kozeschnik, E., 2014, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 610, p. 39-45

    Research output: Contribution to journal › Article › Research › peer-review

  8. 2013
  9. Published

    The influence of microstructure and operating temperature on the fatigue endurance of hot forged Inconel (R) 718 components

    Maderbacher, H., Oberwinkler, B., Gänser, H.-P., Tan, W., Rollett, M. & Stoschka, M., 15 Nov 2013, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 585, p. 123-131

    Research output: Contribution to journal › Article › Research › peer-review

  10. Published

    Activation Parameters for Deformation of Ultrafine-Grained Aluminium as Determined by Indentation Strain Rate Jumps at Elevated Temperature

    Wheeler, J. M., Maier, V., Durst, K., Göken, M. & Michler, J., 2013, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 585, p. 108-113

    Research output: Contribution to journal › Article › Research › peer-review

  11. Published

    Direct or indirect: Influence of type of retained austenite decomposition during tempering on the toughness of a hot-work tool steel

    Lerchbacher, C., Zinner, S. & Leitner, H., 2013, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 564, p. 163-168

    Research output: Contribution to journal › Article › Research › peer-review

  12. Published

    Influence of bulk pre-straining on the size effect in nickel compression pillars

    Schneider, A. S., Kiener, D., Yakacki, C. M., Maier, H. J., Gruber, P. A., Tamura, N., Kunz, M., Minor, A. M. & Frick, C. P., 2013, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 559, p. 147-158 12 p.

    Research output: Contribution to journal › Article › Research › peer-review

Previous 1...6 7 8 9 10 11 12 13 ...18 Next
View graph of relations