Quasi-static and dynamic fracture toughness of a γ-TiAl alloy: Measurement techniques, fractography and interpretation

Publikationen: Beitrag in FachzeitschriftArtikelForschung(peer-reviewed)

Standard

Quasi-static and dynamic fracture toughness of a γ-TiAl alloy: Measurement techniques, fractography and interpretation. / Lintner, Arthur; Pippan, Reinhard; Schloffer, Martin et al.
in: Engineering Fracture Mechanics, Jahrgang 258.2021, Nr. December, 108081, 12.2021.

Publikationen: Beitrag in FachzeitschriftArtikelForschung(peer-reviewed)

Vancouver

Lintner A, Pippan R, Schloffer M, Hohenwarter A. Quasi-static and dynamic fracture toughness of a γ-TiAl alloy: Measurement techniques, fractography and interpretation. Engineering Fracture Mechanics. 2021 Dez;258.2021(December):108081. Epub 2021 Okt 29. doi: 10.1016/j.engfracmech.2021.108081

Bibtex - Download

@article{5bdfb5f1a4dd445a872adb1760894272,
title = "Quasi-static and dynamic fracture toughness of a γ-TiAl alloy: Measurement techniques, fractography and interpretation",
abstract = "Intermetallic titanium aluminides (TiAl) offer an enormous potential for high temperature applications due to their high specific strength, creep and oxidation resistance. However, their use for structural components is limited by their low ductility and fracture toughness. During service, along with a high number of load cycles, the material may also be subjected to unexpected impact loads, which requires therefore knowledge about dynamic material parameters for a damage-tolerant component design. Here we present a feasibility study to determine the fracture toughness of a third generation TiAl-alloy over a wide range of loading rates. Quasi-static crack resistance curves (R-curves) were determined using the direct current potential drop (DCPD) technique. The dynamic experiments were performed with a drop tower with impact velocities ranging from 1 to 10 m/s on pre-cracked SENB specimens. To exclude the influence of inertial forces, the measurements were carried out with strain gauges applied in the elastic near-field of the crack tip. Despite a critical consideration of possible systematic errors of this measurement method, it was found that the dynamic fracture initiation toughness slightly increases up to loading rates of {\.K}I = 106 MPa√m/s. The fracture behaviour of the material and possible reasons for the toughness increase are discussed based on comprehensive fractographic investigations as well as crack path analyses within the microstructure.",
keywords = "Dynamic fracture toughness, Fracture initiation toughness, Titanium aluminide",
author = "Arthur Lintner and Reinhard Pippan and Martin Schloffer and Anton Hohenwarter",
note = "Publisher Copyright: {\textcopyright} 2021 The Authors",
year = "2021",
month = dec,
doi = "10.1016/j.engfracmech.2021.108081",
language = "English",
volume = "258.2021",
journal = "Engineering Fracture Mechanics",
issn = "0013-7944",
publisher = "Elsevier",
number = "December",

}

RIS (suitable for import to EndNote) - Download

TY - JOUR

T1 - Quasi-static and dynamic fracture toughness of a γ-TiAl alloy

T2 - Measurement techniques, fractography and interpretation

AU - Lintner, Arthur

AU - Pippan, Reinhard

AU - Schloffer, Martin

AU - Hohenwarter, Anton

N1 - Publisher Copyright: © 2021 The Authors

PY - 2021/12

Y1 - 2021/12

N2 - Intermetallic titanium aluminides (TiAl) offer an enormous potential for high temperature applications due to their high specific strength, creep and oxidation resistance. However, their use for structural components is limited by their low ductility and fracture toughness. During service, along with a high number of load cycles, the material may also be subjected to unexpected impact loads, which requires therefore knowledge about dynamic material parameters for a damage-tolerant component design. Here we present a feasibility study to determine the fracture toughness of a third generation TiAl-alloy over a wide range of loading rates. Quasi-static crack resistance curves (R-curves) were determined using the direct current potential drop (DCPD) technique. The dynamic experiments were performed with a drop tower with impact velocities ranging from 1 to 10 m/s on pre-cracked SENB specimens. To exclude the influence of inertial forces, the measurements were carried out with strain gauges applied in the elastic near-field of the crack tip. Despite a critical consideration of possible systematic errors of this measurement method, it was found that the dynamic fracture initiation toughness slightly increases up to loading rates of K̇I = 106 MPa√m/s. The fracture behaviour of the material and possible reasons for the toughness increase are discussed based on comprehensive fractographic investigations as well as crack path analyses within the microstructure.

AB - Intermetallic titanium aluminides (TiAl) offer an enormous potential for high temperature applications due to their high specific strength, creep and oxidation resistance. However, their use for structural components is limited by their low ductility and fracture toughness. During service, along with a high number of load cycles, the material may also be subjected to unexpected impact loads, which requires therefore knowledge about dynamic material parameters for a damage-tolerant component design. Here we present a feasibility study to determine the fracture toughness of a third generation TiAl-alloy over a wide range of loading rates. Quasi-static crack resistance curves (R-curves) were determined using the direct current potential drop (DCPD) technique. The dynamic experiments were performed with a drop tower with impact velocities ranging from 1 to 10 m/s on pre-cracked SENB specimens. To exclude the influence of inertial forces, the measurements were carried out with strain gauges applied in the elastic near-field of the crack tip. Despite a critical consideration of possible systematic errors of this measurement method, it was found that the dynamic fracture initiation toughness slightly increases up to loading rates of K̇I = 106 MPa√m/s. The fracture behaviour of the material and possible reasons for the toughness increase are discussed based on comprehensive fractographic investigations as well as crack path analyses within the microstructure.

KW - Dynamic fracture toughness

KW - Fracture initiation toughness

KW - Titanium aluminide

UR - http://www.scopus.com/inward/record.url?scp=85118738437&partnerID=8YFLogxK

U2 - 10.1016/j.engfracmech.2021.108081

DO - 10.1016/j.engfracmech.2021.108081

M3 - Article

AN - SCOPUS:85118738437

VL - 258.2021

JO - Engineering Fracture Mechanics

JF - Engineering Fracture Mechanics

SN - 0013-7944

IS - December

M1 - 108081

ER -