Research output

11 - 20 out of 43Page size: 10
rss feed
  1. 2020
  2. Published

    Causes of the Gloss Transition Defect on High-Gloss Injection-Molded Surfaces

    Gim, J., Han, E., Rhee, B., Friesenbichler, W. & Gruber, D. P., 15 Sept 2020, In: Polymers. 12.2020, 9, 16 p., 2100.

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    Ultra-High Through-Cure of (Meth) Acrylate Copolymers via Photofrontal Polymerization

    Ebner, C., Mitterer, J., Eigruber, P., Stieger, S., Rieß, G. & Kern, W., 1 Jun 2020, In: Polymers. 12, 6, 1291.

    Research output: Contribution to journal › Article › Research › peer-review

  4. Published

    Viscoelastic Modelling of Polymer Melts and Rubber Compounds

    Friesenbichler, W., Stieger, S., Kerschbaumer, R. C., Berger-Weber, G., Neunhäuserer, A. & Mitsoulis, E., 2020, Advances in Polymer Processing 2020 Christian Hopmann Rainer Dahlmann Eds. Proceedings of the International Symposium on Plastics Technology. Springer Vieweg, p. 270-282 12 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  5. 2019
  6. E-pub ahead of print

    Comparison of steady-state and transient thermal conductivity testing methods using different industrial rubber compounds

    Kerschbaumer, R. C., Stieger, S., Gschwandl, M., Hutterer, T., Fasching, M., Lechner, B., Meinhart, L., Hildenbrandt, J., Schrittesser, B., Fuchs, P. F., Berger-Weber, G. & Friesenbichler, W., 26 Sept 2019, (E-pub ahead of print) In: Polymer Testing. 80.2019, December, p. 1-8 8 p., 106121.

    Research output: Contribution to journal › Article › Research

  7. Published

    Influence of dissipation on abrasive wear of a powder metallurgical mold steel in plastics injection molding

    Friesenbichler, W., Zidar, D., Blutmager, A. & Gebauer, T., 16 May 2019, Proceedings of the 11th Tooling Conference & Exhibition. 8 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  8. Published

    Simulative and experimental investigation of rapid heat cycle molding for rubbers

    Hutterer, T., Berger-Weber, G., Mager, C., Fasching, M. A., Pacher, G. A. & Friesenbichler, W., 22 Jan 2019, AIP Conference Proceedings. Vol. 2055. p. 080003-1 - 080003-5 5 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  9. Published

    Thermal Degradation Kinetics of Polypropylene/Clay Nanocomposites Prepared by Injection Molding Compounder

    Kannan Vimalathithan, P., Barile, C., Casavola, C., Arunachalam, S., Battisti, M., Friesenbichler, W. & Vijayakumar, C. T., 1 Jan 2019, In: Polymer Composites. 2019, p. 1-10 10 p.

    Research output: Contribution to journal › Article › Research › peer-review

  10. Published

    Fault detection in rubber injection molding with multivariate statistics

    Hutterer, T., Berger-Weber, G. & Friesenbichler, W., 2019, In: Rubber world. 2019, December, p. 40-44 5 p.

    Research output: Contribution to journal › Article › Research › peer-review

  11. 2018
  12. Published

    A novel hyperbolic slit contraction with constant strain rate for elongational rheology of polymer melts

    Luger, H-J., Löw-Baselli, B., Neunhäuserer, A., Friesenbichler, W. & Miethlinger, J., 9 Nov 2018, In: Polymer Testing. 73.2019, February, p. 104-114 11 p.

    Research output: Contribution to journal › Article › Research › peer-review

  13. Published

    Investigation on the Thermal Degradation Kinetics of Polypropylene/Organically Modified Montmorillonite Nanocomposites with Different Levels of Compatibilizer

    Vimalathithan, P. K., Barile, C., Casavola, C., Vijayakumar, C. T., Arunachalam, S., Battisti, M. & Friesenbichler, W., 9 Oct 2018, In: Macromolecular materials and engineering. 303.2018, December, 8 p., 1800260.

    Research output: Contribution to journal › Article › Research › peer-review

Previous 1 2 3 4 5 Next

Advanced filters

All authors

Reset

to
Reset filters