Research output

191 - 200 out of 413Page size: 10
rss feed
  1. 2013
  2. Published

    Correlation between Rheotens Measurements and Reinforcement of Polymer Nanocomposites in the Injection Molding Compounder

    Battisti, M., Duretek, I., Friesenbichler, W., Guttmann, P. & Pinter, G., 2013, 1st International Conference on Rheology and Modelling of Materials - Book of Abstracts. p. 39-39

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  3. Published

    Deformation Analysis of an Automotive Part by Injection Molding Simulation: Influence of Material Data and Mold Modeling on Prediction Quality

    Luger, H-J., Berger, G., Müller, F., Friesenbichler, W., Beytollahi, I. & Filz, P., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

  4. Published

    Deformation Analysis of an Automotive Part by Injection Molding Simulation: Influence of Material Data and Mold Modelling on Prediction Quality

    Luger, H-J., Berger, G., Müller, F., Friesenbichler, W., Beytollahi, I. & Filz, P., 2013, 29th International Conference of the Polymer Processing Society. p. 59-59

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  5. Published

    Die Wirkung dynamischer Werkzeugtemperierung auf die Oberflächenqualität von Kunststoffteilen

    Pacher, G., Berger, G., Friesenbichler, W. & Gruber, D. P., 2013, 22. Leobener Kunststoff-Kolloquium: Oberlfächen und Grenzflächen in der Polymertechnologie. p. 101-110

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  6. Published

    Elongational viscosity of rubber compounds and improving corresponding models

    Perko, L., Friesenbichler, W., Obendrauf, W., Buchebner, V. & Chaloupka, G., 2013, In: Advances in production engineering & management. 8, p. 126-133

    Research output: Contribution to journal › Article › Research › peer-review

  7. Published

    Grenzflächenphänomene im Mehrkomponenten-Spritzguss

    Kisslinger, T., Bruckmoser, K., Lucyshyn, T., Langecker, G. & Holzer, C., 2013, 22. Leobener Kunststoff-Kolloquium. p. 58-74

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  8. Published

    INFLUENCE OF PROCESS SETTINGS ON THE TOPOGRAPHY OF SINK MARKS

    Pacher, G., Berger, G., Gruber, D. P. & Friesenbichler, W., 2013, ADVANCES IN PLASTICS TECHNOLOGY - Conference Papers. Gliwice, Polen, p. Paper No. 31

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  9. Published

    INTERFACE CONDITIONS OF TWO-SHOT MOLDED PARTS

    Kisslinger, T., Bruckmoser, K., Lucyshyn, T., Langecker, G. & Holzer, C., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

  10. Published

    In-Mold Sensor Concept to calculate process-specific Rheological Properties

    Pacher, G., Berger, G., Friesenbichler, W., Gruber, D. P. & Macher, J., 2013, 29th International Conference of the Polymer Processing Society. p. 48-48

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  11. Published

    Influence of Chain Extender on the Foaming Behavior and on the Mechanical Properteis of Physically Foamed PLA

    Mostafa, H., Geißler, B., Uray, A., Laske, S., Holzer, C. & Langecker, G., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

Previous 1...16 17 18 19 20 21 22 23 ...42 Next

Advanced filters

All authors

Reset

to
Reset filters