Research output

161 - 170 out of 299Page size: 10
rss feed
  1. 2013
  2. Published

    Ausnutzung der Scher- und Dehnerwärmung zur Heizzeitverkürzung; bei der Verarbeitung von Elastomeren

    Perko, L., Friesenbichler, W. & Fasching, M., 2013, In: Österreichische Kunststoff-Zeitschrift. p. 252-254

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    Correlation between Rheotens Measurements and Reinforcement of Polymer Nanocomposites in the Injection Molding Compounder

    Battisti, M., Duretek, I., Friesenbichler, W., Guttmann, P. & Pinter, G., 2013, 1st International Conference on Rheology and Modelling of Materials - Book of Abstracts. p. 39-39

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  4. Published

    Deformation Analysis of an Automotive Part by Injection Molding Simulation: Influence of Material Data and Mold Modeling on Prediction Quality

    Luger, H-J., Berger, G., Müller, F., Friesenbichler, W., Beytollahi, I. & Filz, P., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

  5. Published

    Deformation Analysis of an Automotive Part by Injection Molding Simulation: Influence of Material Data and Mold Modelling on Prediction Quality

    Luger, H-J., Berger, G., Müller, F., Friesenbichler, W., Beytollahi, I. & Filz, P., 2013, 29th International Conference of the Polymer Processing Society. p. 59-59

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  6. Published

    Development and characterization of optoelectronic circuit boards produced by two-photon polymerization using a polysiloxane containing acrylate functional groups

    Woods, R., Feldbacher, S., Langer, G., Satzinger, V., Schmid, G., Leeb, W., Kern, W. & Zidar, D., 2013, In: Applied Optics. 52, p. 388-393

    Research output: Contribution to journal › Article › Research › peer-review

  7. Published

    Die Wirkung dynamischer Werkzeugtemperierung auf die Oberflächenqualität von Kunststoffteilen

    Pacher, G., Berger, G., Friesenbichler, W. & Gruber, D. P., 2013, 22. Leobener Kunststoff-Kolloquium: Oberlfächen und Grenzflächen in der Polymertechnologie. p. 101-110

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  8. Published

    Elongational viscosity of rubber compounds and improving corresponding models

    Perko, L., Friesenbichler, W., Obendrauf, W., Buchebner, V. & Chaloupka, G., 2013, In: Advances in production engineering & management. 8, p. 126-133

    Research output: Contribution to journal › Article › Research › peer-review

  9. Published

    INFLUENCE OF PROCESS SETTINGS ON THE TOPOGRAPHY OF SINK MARKS

    Pacher, G., Berger, G., Gruber, D. P. & Friesenbichler, W., 2013, ADVANCES IN PLASTICS TECHNOLOGY - Conference Papers. Gliwice, Polen, p. Paper No. 31

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  10. Published

    In-Mold Sensor Concept to calculate process-specific Rheological Properties

    Pacher, G., Berger, G., Friesenbichler, W., Gruber, D. P. & Macher, J., 2013, 29th International Conference of the Polymer Processing Society. p. 48-48

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  11. Published

    Influence of Mold Surface Temperature on Polymer Part Warpage in Rapid Heat Cycle Molding

    Berger, G., Pacher, G., Gruber, D. P., Pichler, A. & Friesenbichler, W., 2013, 29th International Conference of the Polymer Processing Society. p. 49-49

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

Previous 1...13 14 15 16 17 18 19 20 ...30 Next

Advanced filters

All authors

Reset

to
Reset filters