Research output

201 - 210 out of 436Page size: 10
rss feed
  1. 2012
  2. Published

    FE2 scheme for simulation of thermo-mechanically induced phase transformations and residual stresses in Ti6A14V components

    Regener, B., Krempaszky, C., Werner, E. & Stockinger, M., 2012, Ti 2011 - Proceedings of the 12th World Conference on Titanium. p. 632-636 5 p. (Ti 2011 - Proceedings of the 12th World Conference on Titanium; vol. 1).

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  3. Published

    FEM-Analyse des Axial-Radial-Umformens als Verfahrenserweiterung des Radialschmiedens

    Kuss, M., Wallner, S. & Buchmayr, B., 2012, Simulation in der Umformtechnik. p. 228-245

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  4. Published

    FEM-Analyse des Axial-Radial-Umformens als Verfahrenserweiterung des Radialschmiedens

    Kuss, M., Wallner, S., Harrer, O-K. & Buchmayr, B., 2012, XXXI. Verformungskundliches Kolloquium. p. 29-33

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  5. Published

    FEM-optimized thermomechanical processing of titanium alloy blades for steam turbines

    Stockinger, M., Zechner, W., Krenn, G. & Weber, G., 2012, Ti 2011 - Proceedings of the 12th World Conference on Titanium. p. 298-301 4 p. (Ti 2011 - Proceedings of the 12th World Conference on Titanium; vol. 1).

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  6. Published

    Functional Mold Coatings for Dynamic Mold Surface Temperature Control in Injection Molding. Simulation of Joule Heating of Thin Films and Development of a Test System.

    Pacher, G., Berger, G., Friesenbichler, W. & Weiß, H., 2012, Abstract Book - The 28th International Conference of Polymer Processing Society (PPS-28). p. 495-495

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  7. Published

    Functional Mold Coatings for Dynamic Mold Surface Temperature Control in Injection Molding. Simulation of Joule Heating of Thin Films and Development of a Test System.

    Pacher, G., Berger, G., Friesenbichler, W. & Weiß, H., 2012.

    Research output: Contribution to conference › Poster › Research › peer-review

  8. Published

    Influence of temperature and strain rate on dynamic softening processes in Allvac® 718Plus™

    Mitsche, S., Sommitsch, C., Huber, D., Stockinger, M. & Poelt, P., 2012, THERMEC 2011. Trans Tech Publications, p. 2440-2445 6 p. (Materials Science Forum; vol. 706-709).

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  9. Published

    Lightweight design by radial forged gear box components

    Hofer, F., Kuss, M., Wallner, S., Buchmayr, B. & Harrer, O-K., 2012, Getriebe in Fahrzeugen. p. 309-319

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  10. Published

    Maßnahmen zur Reparatur und Lebensdauererhöhung von Schmiedewerkzeugen

    Yilkiran, T., Behrens, B-A. & Buchmayr, B., 2012, In: Schmiede-Journal. 2012, März, p. 52-57

    Research output: Contribution to journal › Article › Research › peer-review

  11. Published

    Microstructural characterization of hot deformed Ti-6A1-4V

    Warchomicka, F., Poletti, C. & Stockinger, M., 2012, Ti 2011 - Proceedings of the 12th World Conference on Titanium. p. 729-732 4 p. (Ti 2011 - Proceedings of the 12th World Conference on Titanium; vol. 1).

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

Previous 1...17 18 19 20 21 22 23 24 ...44 Next

Advanced filters

All authors

Reset

to
Reset filters