Walter Friesenbichler

(Former)

111 - 120 out of 290Page size: 10
Sort by: Title

Research output

  1. Published

    Novel approach to the measurement of the visual perceptibility of sink marks on injection molding parts

    Gruber, D. P., Berger, G., Pacher, G. & Friesenbichler, W., 2011, In: Polymer Testing. p. 651-656

    Research output: Contribution to journal › Article › Research › peer-review

  2. Published

    New ways for the characterization of appearance properties of plastic products and components close to human vision

    Gruber, D. P., Berger, G. & Friesenbichler, W., 2013, THE PROCEEDINGS OF THE AUSTRIAN – SLOVENIAN POLYMER MEETING 2013. Ljubljana, p. 11-13

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  3. Published

    New Rheological Injection Mould to Measure Pressure Dependent Viscosity in High Shear Rate Range

    Friesenbichler, W., Rajganesh Jegadeesan, X., Duretek, I. & Ramesh Kumar, S., 2009,

    PPS-25 Program & Abstracts

    .     p. 185-185

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  4. Published

    NEW METHODS FOR QUALITY CONTROL OF INJECTION-MOLDED PARTS

    Macher, J., Gruber, D. P., Berger, G. & Friesenbichler, W., 2013, ANTEC 2013 Conference and Tradeshow. p. 1-4

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  5. Published

    New Insights into Feedstock Behaviour and Injection Moulding Simulation for PIM

    Kukla, C., Duretek, I., Friesenbichler, W. & Thornagel, M., 2008, Euro PM2008 Proceedings Vol 2. p. 287-292

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  6. Published

    Neue Maplan-Gummispritzmaschine für die Kunststofftechnik Leoben

    Friesenbichler, W., 2011, In: Österreichische Kunststoff-Zeitschrift. p. 293-293

    Research output: Contribution to journal › Article › Research › peer-review

  7. Published

    Nachruf auf O.Univ.-Prof. i. R. Dr. rer. nat. Dipl.-Phys. Werner Knappe

    Friesenbichler, W., 2011, In: Österreichische Kunststoff-Zeitschrift. p. 294-295

    Research output: Contribution to journal › Article › Research › peer-review

  8. Published

    MULTI-FUNCTIONAL INJECTION MOLD FOR EXAMINING THE INFLUENCE OF RAPID HEAT CYCLE MOLDING ON POLYMER MORPHOLOGY

    Pacher, G., Berger, G. & Friesenbichler, W., 2013, Tagungsband der 3. Tagung Innovation Messtechnik. p. 25-30

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  9. Published

    More Gloss, Fewer Weld Lines With Variothermal Molding

    Berger, G., Roock, S., Steinbichler, G., Gießauf, J., Gruber, D. P. & Friesenbichler, W., 2013, In: Plastics technology. 59, 3, p. 30, 60-35, 62

    Research output: Contribution to journal › Article › Research › peer-review

  10. Published

    Moffatt-Eddies: Existing in Rubber Processing?

    Kerschbaumer, R., Lechner, B. & Friesenbichler, W., Apr 2017, 26. Leobener Kunststoff-Kolloquium 20. und 21. April 2017: Schriftenreihe Kunststofftechnik. Friesenbichler, W. & Berger, G. (eds.). Leoben, Vol. 7. p. 257-258 2 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

Previous 1...8 9 10 11 12 13 14 15 ...29 Next
View graph of relations

Latest Research Output

View more (290)