Walter Friesenbichler
(Former)
Research output
- Published
Reduction of cure time in elastomer processing
Perko, L. & Friesenbichler, W., May 2015, In: Rubber, fibres, plastics international. Issue 02/2015, p. 117-121 5 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Die Wirkung dynamischer Werkzeugtemperierung auf die Oberflächenqualität von Kunststoffteilen
Pacher, G., Berger, G., Friesenbichler, W. & Gruber, D. P., 2013, 22. Leobener Kunststoff-Kolloquium: Oberlfächen und Grenzflächen in der Polymertechnologie. p. 101-110Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Influence of cavity pressure and injection rate on the surface roughness of PP, PC, ABS and ABS-PC
Pacher, G., Berger, G. & Friesenbichler, W., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
In-Mold Sensor Concept to calculate process-specific Rheological Properties
Pacher, G., Berger, G., Friesenbichler, W., Gruber, D. P. & Macher, J., 2013, 29th International Conference of the Polymer Processing Society. p. 48-48Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
MULTI-FUNCTIONAL INJECTION MOLD FOR EXAMINING THE INFLUENCE OF RAPID HEAT CYCLE MOLDING ON POLYMER MORPHOLOGY
Pacher, G., Berger, G. & Friesenbichler, W., 2013, Tagungsband der 3. Tagung Innovation Messtechnik. p. 25-30Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Functional Mold Coatings for Dynamic Mold Surface Temperature Control in Injection Molding. Simulation of Joule Heating of Thin Films and Development of a Test System.
Pacher, G., Berger, G., Friesenbichler, W. & Weiß, H., 2012, Abstract Book - The 28th International Conference of Polymer Processing Society (PPS-28). p. 495-495Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Functional Mold Coatings for Dynamic Mold Surface Temperature Control in Injection Molding. Simulation of Joule Heating of Thin Films and Development of a Test System.
Pacher, G., Berger, G., Friesenbichler, W. & Weiß, H., 2012.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Influence of cavity pressure and injection rate on the surface roughness of PP, PC, ABS and ABS-PC
Pacher, G., Berger, G. & Friesenbichler, W., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Influence of Thermal Conductivity of PP-Based Compounds on Surface Roughness of Rapid Heat Cycle Injection Molded Parts
Pacher, G., Geissler, B., Macher, J., Berger, G., Gruber, D. P. & Friesenbichler, W., 2014, 30th International Conference of the Polymer Processing Scociety: DIGITAL BOOK OF ABSTRACTS AND CONFERENCE PAPERS. p. 10-136Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
INFLUENCE OF PROCESS SETTINGS ON THE TOPOGRAPHY OF SINK MARKS
Pacher, G., Berger, G., Gruber, D. P. & Friesenbichler, W., 2013, ADVANCES IN PLASTICS TECHNOLOGY - Conference Papers. Gliwice, Polen, p. Paper No. 31Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
