Tanja Lube
Research output
- 2021
- Published
Size effect assessment by Weibull’s approach and the coupled criterion
Doitrand, A., Henry, R., Lube, T. & Meille, S., 10 Sept 2021, In: Engineering Fracture Mechanics. 256, 107979.Research output: Contribution to journal › Article › Research › peer-review
- Published
Comparison of biaxial strength measured with the Ball-on-Three-Balls- and the Ring-on-Ring-test
Staudacher, M., Lube, T., Schlacher, J. & Supancic, P., Jun 2021, In: Open ceramics. 6, June, 10 p., 100101.Research output: Contribution to journal › Article › Research › peer-review
- Published
Fracture Toughness Measurement
Lube, T., 2021, Encyclopedia of Materials: Technical Ceramics and Glasses. Oxford: Elsevier, Vol. 1. p. 762-774Research output: Chapter in Book/Report/Conference proceeding › Chapter › Research
- 2020
- Published
Influence of the Infill Orientation on the Properties of Zirconia Parts Produced by Fused Filament Fabrication
Cano Cano, S., Lube, T., Huber, P., Gallego, A., Naranjo, J. A., Berges, C., Schuschnigg, S., Herranz, G., Kukla, C., Holzer, C. & Gonzalez-Gutierrez, J., 15 Jul 2020, In: Materials. 13.2020, 14, 19 p., 3158.Research output: Contribution to journal › Article › Research › peer-review
- E-pub ahead of print
Strength of additive manufactured alumina
Schlacher, J., Lube, T., Harrer, W., Mitteramskogler, G., Schwentenwein, M., Danzer, R. & Bermejo, R., 21 Apr 2020, (E-pub ahead of print) In: Journal of the European Ceramic Society. 40.2020, 14, p. 4737-4745 9 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Influence of WC-Co hard metal microstructure on defect density, initiation and propagation kinetics of fatigue cracks starting at intrinsic and artificial defects under a negative stress ratio
Klünsner, T., Lube, T., Gettinger, C., Walch, L. & Pippan, R., 12 Feb 2020, In: Acta materialia. 188, p. 30-39Research output: Contribution to journal › Article › Research › peer-review
- 2019
- Published
Strength of Lithography-Based Alumina
Schlacher, J. C., Lube, T., Mitteramskogler, G., Schwentenwein, M. & Danzer, R., 9 Sept 2019.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Biaxiale Festigkeitsprüfung von Keramiken
Supancic, P. H., Lube, T. & Danzer, R., 13 Feb 2019.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Festigkeit von additiv gefertigtem Aluminiumoxid
Lube, T., Schlacher, J. C., Harrer, W. S., Danzer, R., Mitteramslkogler, G. & Schwentenwein, M., 13 Feb 2019.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Fatigue behaviour of WC-Co hard metal under stress ratio and effectively loaded volume relevant to metalworking tool failure
Klünsner, T., Jonke, M., Supancic, P., Gettinger, C., Krobath, M., Lube, T., Marsoner, S. & Glätzle, J., 4 Jan 2019, In: International Journal of Refractory Metals and Hard Materials. 80, p. 97-103 7 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Fracture toughness of Silicon Nitride Measured by the Surface Crack in Flexure (SCF) Test Method
Nindhia, T. G. T. & Lube, T., 2019, In: IOP Conference Series: Materials Science and Engineering. 622, 012001.Research output: Contribution to journal › Article › Transfer › peer-review
- Published
Single Edge Precrack V-Notched Beam (SEPVNB) Fracture Toughness Testing on Silicon Nitride
Nindhia, T. G. T. & Lube, T., 2019, Materials science forum. Trans Tech Publications, Vol. 962. p. 205-209 5 p. (Materials Science Forum).Research output: Chapter in Book/Report/Conference proceeding › Chapter › Research
- 2018
- Published
Corrigendum to "Surface Crack in Tension or in Bending - A Reassessment of the Newman and Raju Formula in Respect to Fracture Toughness Measurements in Brittle Materials" [J. Eur. Ceram. Soc. 32 (8) (2012) 1491–1501]
Strobl, S., Supancic, P., Lube, T. & Danzer, R., 2018, In: Journal of the European Ceramic Society. p. 355-358 4 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Fracture Toughness (KIC) of Lithography Based Manufactured Alumina Ceramic
Nindhia, T. G. T., Schlacher, J. C. & Lube, T., 2018, In: IOP Conference Series: Materials Science and Engineering. 012022.Research output: Contribution to journal › Article › Research › peer-review
- Published
Fracture toughness of silicon nitride balls via thermal shock
Strobl, S., Adlmann, F. A., Supancic, P., Lube, T., Danzer, R. & Schöppl, O., 2018, In: Journal of the European Ceramic Society. p. 1278–1287Research output: Contribution to journal › Article › Research › peer-review
- Published
Fracture toughness testing of biomedical ceramic-based materials using beams, plates and discs
Belli, R., Wendler, M., Petschelt, A., Lube, T. & Lohbauer, U., 2018, In: Journal of the European Ceramic Society. 38, 16, p. 5533-5544 12 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Mechanische Eigenschaften von gedruckten Keramiken
Lube, T., Schlacher, J., Harrer, W., Danzer, R., Mitteramskogler, G. & Schwentenwein, M., 2018, Praktische Metallographie Sonderband. Vol. 52. p. 229-234Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- 2017
- Published
Additive Fertigung von Keramiken
Lube, T. & Harrer, W. S., 13 Nov 2017.Research output: Contribution to conference › Poster › Transfer
- Published
Strength of Al2O3-Ceramic Produced by the LCM Additive Manufacturing Technology
Lube, T., Schlacher, J. C., Harrer, W. S., Mitteramskogler, G., Schwentenwein, M. & Danzer, R., 12 Jul 2017.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Chairside CAD/CAM materials. Part 2: flexural strength testing
Belli, R., Wendler, M., Petschelt, A., Mevec, D., Lube, T., Harrer, W., Danzer, R. & Lohbauer, U., 2017, In: Dental Materials. 33, 1, p. 99-109 11 p.Research output: Contribution to journal › Article › Research › peer-review
