Martin Spörk

21 - 40 out of 49Page size: 20

Research output

  1. 2018
  2. Published

    The consequences of different printing chamber temperatures in extrusion-based additive manufacturing

    Spörk, M., Arbeiter, F., Raguz, I., Traxler, G., Schuschnigg, S., Cardon, L. & Holzer, C., 21 Sept 2018.

    Research output: Contribution to conference › Paper › peer-review

  3. Published

    Anisotropic properties of oriented short carbon fibre filled polypropylene parts fabricated by extrusion-based additive manufacturing

    Spoerk, M., Savandaiah, C., Arbeiter, F., Traxler, G., Cardon, L., Holzer, C. & Sapkota, J., 11 Jun 2018, In: Composites Part A: Applied Science and Manufacturing. 113.2018, October, p. 95-104 10 p.

    Research output: Contribution to journal › Article › Research › peer-review

  4. Published

    Facile and Low-Cost Route for Sensitive Stretchable Sensors by Controlling Kinetic and Thermodynamic Conductive Network Regulating Strategies

    Duan, L., D'hooge, D. R., Spörk, M., Cornillie, P. & Cardon, L., 29 May 2018, In: ACS Applied Materials & Interfaces. 10.2018, 26, p. 22678-22691 14 p.

    Research output: Contribution to journal › Article › Research › peer-review

  5. Published

    Adhesion of standard filament materials to different build platforms in material extrusion additive manufacturing

    Schuschnigg, S., Gonzalez-Gutierrez, J., Spörk, M., Sapkota, J. & Holzer, C., 21 May 2018, 34 th International Conference of the Polymer Processing society. Liu, S.-J. (ed.). Taipei, Taiwan, Vol. 34. 1 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  6. Published

    Polypropylene Filled With Glass Spheres in Extrusion‐Based Additive Manufacturing: Effect of Filler Size and Printing Chamber Temperature

    Spörk, M., Arbeiter, F., Raguž, I., Weingrill, G., Fischinger, T., Traxler, G., Schuschnigg, S., Cardon, L. & Holzer, C., 16 May 2018, In: Macromolecular materials and engineering. 303.2018, 7, 15 p., 1800179.

    Research output: Contribution to journal › Article › Research › peer-review

  7. Published

    Material selection, testing and validation of additively manufactured components

    Wiener, J., Arbeiter, F., Spörk, M., Gosch, A. & Pinter, G. G., 9 May 2018.

    Research output: Contribution to conference › Paper › peer-review

  8. Published

    Optimisation of the Adhesion of Polypropylene-Based Materials during Extrusion-Based Additive Manufacturing

    Spörk, M., Gonzalez-Gutierrez, J., Lichal, C., Cajner, H., Berger, G., Schuschnigg, S., Cardon, L. & Holzer, C., 2 May 2018, In: Polymers. 10.2018, 5, 16 p., 490.

    Research output: Contribution to journal › Article › Research › peer-review

  9. Published

    Strukturbauteile aus dem 3D-Drucker: begleitende Werkstoffprüfung zur Eigenschaftsoptimierung

    Arbeiter, F., Wiener, J., Spörk, M. & Pinter, G. G., 20 Apr 2018, p. 1. 4 p.

    Research output: Contribution to conference › Paper

  10. Published

    Entwicklungen im Bereich Fused Filament Fabrication

    Schuschnigg, S., Spörk, M. & Holzer, C., 19 Apr 2018, 27. Leobener Kunststoff-Kolloquium: Print & Coat- Polymere in Druck- und Beschichtungstechnologien. Kern, W. (ed.). Leoben: Eigenverlag, Vol. 27. p. 19-34

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  11. Published

    Polypropylene/Cellulose Composites for Material Extrusion Additive Manufacturing

    Kaynak, B., Spörk, M., Shirole, A., Ziegler, W. & Sapkota, J., 14 Apr 2018, In: Macromolecular materials and engineering. 303.2018, 5, 8 p., 1800037.

    Research output: Contribution to journal › Article › Research › peer-review

  12. Published

    Influence of strand orientation on mechanical properties in near homogeneous FFF produced PLA parts

    Wiener, J., Arbeiter, F., Spörk, M., Gosch, A. & Pinter, G. G., 27 Mar 2018.

    Research output: Contribution to conference › Poster › Research

  13. Published

    Fracture mechanical characterization and lifetime estimation of near-homogeneous components produced by fused filament fabrication

    Arbeiter, F., Spoerk, M., Wiener, J., Gosch, A. & Pinter, G., 5 Jan 2018, In: Polymer Testing. 66.2018, April, p. 105-113 9 p.

    Research output: Contribution to journal › Article › Research › peer-review

  14. Published

    Optimisation of the Mechanical Properties and Processing of Polypropylene and Poly(Lactic Acid) Parts Produced by Extrusion-Based Additive Manufacturing

    Spörk, M., 2018

    Research output: Thesis › Doctoral Thesis

  15. 2017
  16. Published

    Optimization of Mechanical Properties of Glass-Spheres-Filled Polypropylene Composites for Extrusion-Based Additive Manufacturing

    Spörk, M., Savandaiah, C., Arbeiter, F., Sapkota, J. & Holzer, C., 26 Dec 2017, In: Polymer Composites. 40.2019, 2, p. 638-651 14 p.

    Research output: Contribution to journal › Article › Research › peer-review

  17. Published

    3D printing conditions determination for feedstock used in fused filament fabrication (FFF) of 17-4PH stainless steel parts

    Gonzalez-Gutierrez, J., Godec, D., Guran, R., Spörk, M., Kukla, C. & Holzer, C., 15 Nov 2017, In: Metalurgija : casopis Izdaje Tehnoloski Fakultet Sveucilista u Zagrebu, Odjeli u Sisku, Institut za Metalurgiju i Zeljezara Sisak = Metallurgy. 57.2018, 1-2, p. 117-120 4 p., 669.15:621.775:669.015:66.049.4:621.385.833=111.

    Research output: Contribution to journal › Article › Research › peer-review

  18. Published

    Effect of the printing bed temperature on the adhesion of parts produced by fused filament fabrication

    Spörk, M., Gonzalez-Gutierrez, J., Sapkota, J., Schuschnigg, S. & Holzer, C., 8 Nov 2017, In: Plastics, rubber and composites. 47.2018, 1, p. 17-24 8 p.

    Research output: Contribution to journal › Article › Research › peer-review

  19. E-pub ahead of print

    Shrinkage and Warpage Optimization of Expanded-Perlite-Filled Polypropylene Composites in Extrusion-Based Additive Manufacturing

    Spörk, M., Sapkota, J., Weingrill, G., Fischinger, T., Arbeiter, F. & Holzer, C., 4 Jul 2017, (E-pub ahead of print) In: Macromolecular materials and engineering. 302.2017, 10, 13 p., 1700143.

    Research output: Contribution to journal › Article › Research › peer-review

  20. E-pub ahead of print

    Parametric optimization of intra- and inter-layer strengths in parts produced by extrusion-based additive manufacturing of poly(lactic acid)

    Spörk, M., Arbeiter, F., Cajner, H., Sapkota, J. & Holzer, C., 26 Jun 2017, (E-pub ahead of print) In: Journal of Applied Polymer Science. 134.2017, 41, 15 p., 45401.

    Research output: Contribution to journal › Article › Research › peer-review

  21. Published

    Properties of glass filled polypropylene for Fused Filament Fabrication

    Spörk, M., Savandaiah, C., Arbeiter, F., Schuschnigg, S. & Holzer, C., May 2017.

    Research output: Contribution to conference › Paper › peer-review

  22. 2016
  23. Published

    Special Materials and Technologies for Fused Filament Fabrication

    Spörk, M., Gonzalez-Gutierrez, J., Schuschnigg, S. & Holzer, C., 11 Oct 2016, 2016 PPS Asia/Australia Conference. Chengdu, China, p. 1-5 5 p.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

Previous 1 2 3 Next
View graph of relations

Latest Research Output

View more (49)