Heinz Gottfried Leitner
(Former)
Research output
- Published
Computed Tomography for the Evaluation of the Influence of Porosity on Stress Distribution
Powazka, D., Brune, M., Eichlseder, W., Leitner, H. & Oppermann, H., 2008, In: Archives of Foundry Engineering (AFE ; quarterly). 8, Special issue 1, p. 291-294Research output: Contribution to journal › Article › Research › peer-review
- Published
Computed Tomography- an Alternative and Complement to Traditional Metallographic Investigations of Porosity in Cast Aluminium
Powazka, D., Brune, M., Eichlseder, W., Leitner, H. & Oppermann, H., 2008, Computed Tomography- an Alternative and Complement to Traditional Metallographic Investigations of Porosity in Cast Aluminium. p. 51-66Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Fertigungsbedingte Einflüsse auf die Schwingfestigkeit von Al-Gussbauteilen – Neue Erkenntnisse für Druckgussbauteile
Powazka, D., Brune, M., Oppermann, H., Eichlseder, W. & Leitner, H., 2008, In: Gießerei-Rundschau. 55, p. 92-99Research output: Contribution to journal › Article › Research › peer-review
- Published
Leichtbau, Betriebsfestigkeit und Verschleiß - Optimierung unter Berücksichtigung dreier konträrer Ziele am Beispiel hochbelasteter Schneidzähne
Redik, S., Mösenbacher, A., Guster, C., Oberwinkler, C., Leitner, H. & Feyerer, C., 2011, Konsequenter Leichtbau und Festigkeitssteigerung - (k)ein Widerspruch?. p. 253-264Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Leichtbau, Betriebsfestigkeit und Verschleiß – Optimierung unter Berücksichtigung dreier konträrer Ziele am Beispiel hochbelasteter Schneidzähne
Redik, S., Mösenbacher, A., Guster, C., Oberwinkler, C., Feyerer, C. & Leitner, H., 2011.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Ermittlung von Umlaufbiegefestigkeiten von gekerbten Proben zur Entwicklung neuer Werkstoff-Plasmanitrier-Kombinationen am Beispiel von Hochleistungszahnrädern
Reithofer, G., Leitner, H., Eichlseder, W. & Schuch, F., 2007, In: HTM - journal of heat treatment and materials . 03, p. 134-138Research output: Contribution to journal › Article › Research › peer-review
- Published
A High Cycle Fatigue Model for Al-Alloys based on Low Cycle Fatigue Data and Notch Sensitivity
Riedler, M., Araujo, B., Leitner, H. & Eichlseder, W., 2005, A High Cycle Fatigue Model for Al-Alloys based on Low Cycle Fatigue Data and Notch Sensitivity. DAS Secretariat, p. 178-179Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Analysis and simulation of heat treatment processes for fatigue and fracture optimization of forged aircraft engine and structural parts
Riedler, M., Stockinger, M., Stoschka, M., Oberwinkler, B., Tan, W. & Leitner, H., 2009, Aeromat2009. p. 11-12Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Lifetime simulation of thermo-mechanically loaded components
Riedler, M., Leitner, H., Prillhofer, B., Winter, G. & Eichlseder, W., 2007, In: Meccanica. 42, p. 47-59Research output: Contribution to journal › Article › Research › peer-review
- Published
Numerischer Vergleich des Kontaktverhaltens verschiedener Prüfverfahren
Stoschka, M., Grün, F., Godor, I. & Leitner, H., 2007Research output: Book/Report › Commissioned report › Transfer › peer-review
