Department Polymer Engineering and Science
Organisational unit: Departments and Institutes
Research output
- Published
On the Use of Bionic Cooling Structures in Injection Molding
Berger, G., Zorn, D., Bodor, C., Friesenbichler, W. & Bevc, F., 22 Sept 2016, p. 155-161. 7 p.Research output: Contribution to conference › Presentation › Research › peer-review
- Published
On the Use of Bionic Cooling Structures in Injection Molding
Berger, G., Zorn, D., Bodor, C., Friesenbichler, W. & Bevc, F., 22 Sept 2016, p. 155-161. 7 p.Research output: Contribution to conference › Paper › peer-review
- Published
On the Use of Bionic Cooling Structures in Injection Molding
Berger, G., Zorn, D., Bodor, C., Friesenbichler, W. & Bevc, F., 22 Sept 2016, Conference Proceedings: 7th bi-annual International Conference of Polymers & Moulds Innovations. Gent, p. 155-161 7 p. 21Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Influence of mold surface temperature on polymer part warpage in rapid heat cycle molding
Berger, G. R., Pacher, G. A., Pichler, A., Friesenbichler, W. & Gruber, D. P., 2014, Proceedings of PPS 2013 - 29th International Conference of the Polymer Processing Society, Conference Papers. Vol. 1593. p. 189-194 6 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Einsatz der Simulation in der systematischen Bauteilentwicklung
Berger, G. & Friesenbichler, W., 27 Feb 2014, p. 1-38. 38 p.Research output: Contribution to conference › Presentation › Research › peer-review
- Published
Characterization of slow crack growth resistance of polyethylene pipe grades with cyclic cracked round bar (CRB) test in correlation to strain hardening (SH) test
Berger, I. J., Frank, A., Arbeiter, F. & Pinter, G., 8 May 2017.Research output: Contribution to conference › Paper › peer-review
- Published
Advanced Manufacturing ganzheitlich betrachtet – Von der Produktentwicklung zum Null-Fehler-Serienprozess
Berger, G., Apr 2017, 26. Leobener Kunststoff-Kolloquium 20. und 21. April 2017: Schriftenreihe Kunststofftechnik. Friesenbichler, W. & Berger, G. (eds.). Leoben, Vol. 7. p. 53-65 13 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Auslegung konturnaher Kühlsysteme für Spritzgießwerkzeuge. Vergleich von SLM-gedruckten mit hochwärmeleitfähigen konventionellen Formeinsätzen
Berger, G., Zorn, D., Panzl, G. & Bevc, F., Apr 2017, 26. Leobener Kunststoff-Kolloquium 20. und 21. April 2017: Schriftenreihe Kunststofftechnik. Friesenbichler, W. & Berger, G. (eds.). Leoben, Vol. 7. p. 229-243 15 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Auslegung konturnaher Kühlsysteme für Spritzgießwerkzeuge. Vergleich von SLM-gedruckten mit hochwärmeleitfähigen konventionellen Formeinsätzen
Berger, G., Zorn, D., Panzl, G. & Bevc, F., 21 Apr 2017, p. 229-243. 15 p.Research output: Contribution to conference › Presentation › Research › peer-review
- Published
Advanced Manufacturing ganzheitlich betrachtet – Von der Produktentwicklung zum Null-Fehler-Serienprozess
Berger, G., 20 Apr 2017, p. 53-65. 13 p.Research output: Contribution to conference › Presentation › Research › peer-review
