Chair of Processing of Composites and Design for Recycling (270)
Organisational unit: Chair
1 - 10 out of 372Page size: 10
Research output
- Published
Spritzgießcompoundieren im Recycling von Post-Consumer PP Abfällen
Zidar, D., Krempl, N., Shahroodi, Z., Kirschnick, U. & Holzer, C., 1 Sept 2024, In: Jahresmagazin Kunststofftechnik : Ingenieurwissenschaften ... : im Fokus . 2024, 01, p. 38-42 5 p.Research output: Contribution to journal › Article › Research
- Published
Experimental characterisation of textile compaction response: a benchmark exercise
Young, A., Aktas, A., May, D., Endruweit, A., Lomov, S. V., Advani, S. G., Hubert, P., Abaimov, S. G., Abliz, D., Akhatov, I., Ali, M. A., Allaoui, S., Allen, T., Berg, D. C., Bickerton, S., Caglar, B., Causse, P., Chiminelli, A., Comas-Cardona, S. & Danzi, M. & 30 others, , Dec 2020, In: Composites Part A: Applied Science and Manufacturing.Research output: Contribution to journal › Article › Research › peer-review
- Published
Out-of-plane permeability measurement for reinforcement textiles: A benchmark exercise
Yong, A., Aktas, A., May, D., Endruweit, A., Advani, S. G., Hubert, P., Abaimov, S. G., Abliz, D., Akhatov, I., Ali, M. A., Allen, T., Berg, D. C., Bickerton, S., Brauner, C., Brütsch, D., Caglar, B., Causse, P., Chiminelli, A., Cohades, A. & Comas-Cardona, S. & 32 others, , Sept 2021, In: Composites Part A: Applied Science and Manufacturing. 148.2021, September, 16 p., 106480.Research output: Contribution to journal › Article › Research › peer-review
- Published
INLINE PROCESS MONITORING AND FAILURE MANAGEMENT CONCEPT FOR ATL
Yadav, N., Schledjewski, R. & Fauster, E., 2024, Proceedings of the 21st European Conference on Composite Materials: Volume 5 - Manufacturing. p. 497-502 6 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Parametric effect on inline width control for thermoplastic automated tape layup
Yadav, N. & Schledjewski, R., Aug 2023.Research output: Contribution to conference › Paper
- Published
Residual strain and structural health monitoring for automated tape layup using HiBi FBG sensor
Yadav, N., 2022.Research output: Contribution to conference › Abstract
- Published
In- and off-line NDT in automated in-situ consolidation tape layup
Yadav, N., Gürocak, M., Galic, A., Adam, R. & Schledjewski, R., Sept 2021, SAMPE EUROPE Conference and Exhibition 2021: Baden, Switzerland, 28-30 September 2021.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Improved layup quality during automated thermoplastic tape layup – Inline detection of consolidation force and tape geometry
Yadav, N. & Schledjewski, R., 2022.Research output: Contribution to conference › Abstract
- Published
Selective comparison of heating sources for thermoplastic Automated Tape Placement
Yadav, N. & Schledjewski, R., May 2019, Automated Composites Manufacturing (ACM4): Fourth International Symposium. Hoa, S. V. (ed.). 8 p. 1Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Online thermography inspection for automated tape layup
Yadav, N., Oswald-Tranta, B., Schledjewski, R. & Habicher, M., 2020, Thermosense: Thermal Infrared Applications XLII. Oswald-Tranta, B. & Zalameda, J. N. (eds.). SPIE, Vol. 11409. 114090H. (Proceedings of SPIE).Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
