Chair of Polymer Processing (350)
Organisational unit: Chair
Research output
- 2009
- Published
On the evaluation of the visual impact of sink marks of injection molded parts
Pacher, G. A., 2009Research output: Thesis › Master's Thesis
- Published
Physical Model for the Expansion Injection Molding Process and Degradation Effects on the Injection Molded Parts due to Extreme Processing Conditions
Jegadeesan, R., Friesenbichler, W., Langecker, G. & Steinbichler, G., 2009Research output: Non-textual form › Web publication/site › Research
- Published
Physikalisches Schäumen
Piontek, M., Laske, S. & Holzer, C., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
PIM - Feedstocks
Duretek, I., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Polymere Nanocomposites
Laske, S., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Polymer nanocomposites prepared by melt mixing: From laboratory to semi-industrial scale
Kracalik, M., Laske, S. & Holzer, C., 2009, Advances in Plastics Technology - APT09 - Abstracts and Papers. p. 5-6Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Polymer-Schichtsilikat Nanocompisites: Vom Labor zum industriellen Compoundieren
Kracalik, M., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Pressure dependent viscosity and its importance for injection molding simulations
Rajganesh Jegadeesan, X., Friesenbichler, W., Duretek, I., Filz, P. & Webelhaus, K., 2009, Conference Proceedings. p. 217-222Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Replication of a draw-polished cavity surface into PP and PC. Influence of flow length, wall thickness and injection molding parameters
Burgsteiner, M., Berger, G. & Friesenbichler, W., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Replication of a draw-polished cavity surface into PP and PC. Influence of flow length, wall thickness and injection molding parameters
Burgsteiner, M., Berger, G. & Friesenbichler, W., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Rheologische Analyse
Duretek, I., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Semi-industrial approach for wear measurement in injection moulds
Friesenbichler, W. & Oláh, L., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Simulation Aufheizprozess Thermoformen
Fertschej, A., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Simulation des Aufheizprozesses
Fertschej, A., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Simulation von Extrusionswerkzeugen
Fertschej, A., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Spritzgießsimulation
Lucyshyn, T., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Structure Replication in Injection Moulding
Berger, G. & Friesenbichler, W., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Structure Replication in Injection Moulding
Berger, G. & Friesenbichler, W., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Studies of the melting behaviour of polypropylene nanocomposites using x-ray diffraction
Feuchter, M., Maier, G., Pinter, G., Kracalik, M., Laske, S. & Langecker, G., 2009.Research output: Contribution to conference › Poster › Research › peer-review
- Published
Studies on the melting behavior of polypropylene nano-composites using X-ray diffraction and differential scanning calorimetry
Feuchter, M., Maier, G., Pinter, G., Kracalik, M., Laske, S. & Langecker, G., 2009, ANTEC 2009 Society of Plastics Engineers' Annual Technical Conference. p. 2642-2646Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
