Chair of Mechanical Engineering (140)
Organisational unit: Chair
691 - 700 out of 1,376Page size: 10
Research output
- Published
Lifetime Evaluation of Hot Forged Aerospace Components by Linking Microstructural Evolution and Fatigue Behaviour
Maderbacher, H., 2010, Fatigue 2010 Book of Abstracts. p. 297-297Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Bewertung der Beanspruchung eines Aktuatorhebels mittels FEM
Maderbacher, H., Fröschl, J. & Christiner, T., 2008Research output: Book/Report › Commissioned report › Transfer › peer-review
- Published
The influence of microstructure and operating temperature on the fatigue endurance of hot forged Inconel® 718 components
Maderbacher, H., Oberwinkler, B., Gänser, H.-P., Tan, W., Rollett, M. & Stoschka, M., 2013, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. Volume 585, p. 123-131Research output: Contribution to journal › Article › Research › peer-review
- Published
Lifetime optimization of hot forged aerospace components by linking microstructural evaluation and fatigue behaviour
Maderbacher, H., Gänser, H.-P., Riedler, M., Stoschka, M., Stockinger, M. & Eichlseder, W., 2011, Euro Superalloys 2010. Trans Tech Publications, p. 162-167 (Advanced materials research; vol. 278).Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Untersuchung der Eigenspannungsentstehung bei der spanenden Formgebung Drehen mittels Finite Elemente Simulation
Maderbacher, H., 2008, 108 p.Research output: Thesis › Diploma Thesis
- Published
Erstellung einer geschlossenen Simulationskette zur Optimierung der Schwingfestigkeit von geschmiedeten Bauteilen aus Nickelbasislegierungen
Maderbacher, H., 2013Research output: Thesis › Doctoral Thesis
- Published
The influence of microstructure and operating temperature on the fatigue endurance of hot forged Inconel (R) 718 components
Maderbacher, H., Oberwinkler, B., Gänser, H.-P., Tan, W., Rollett, M. & Stoschka, M., 15 Nov 2013, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 585, p. 123-131Research output: Contribution to journal › Article › Research › peer-review
- Published
Link from the microstructure to the fatigue lifteime of forged inconel 718 components
Maderbacher, H., Gänser, H. P., Riedler, M., Stoschka, M. & Eichlseder, W., 1 Jan 2009, 26th Danubia-Adria Symposium on Advances in Experimental Mechanics. p. 59-60 2 p.Research output: Chapter in Book/Report/Conference proceeding › Conference contribution
- Published
Reproducibility of navigation based kinematic analysis of the knee – A cadaveric investigation
Maderbacher, G., Keshmiri, A., Springorum, H. R., Maderbacher, H., Grifka, J. & Baier, C., 1 Jan 2019, In: Journal of orthopaedic science : official journal of the Japanese Orthopaedic Association . 24.2019, 1, p. 128-135 8 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Rotation of intramedullary alignment rods affects distal femoral cutting plane in total knee arthroplasty
Maderbacher, G., Matussek, J., Keshmiri, A., Greimel, F., Baier, C., Grifka, J. & Maderbacher, H., 1 Nov 2018, In: Knee surgery, sports traumatology, arthroscopy : KSSTA ; official clinical journal of ESSKA. 26, 11, p. 3311-3316 6 p.Research output: Contribution to journal › Article › Research › peer-review
