Polymer Testing, ‎0142-9418

Journal

ISSNs0142-9418
31 - 40 out of 51Page size: 10
Sort by: Title

Research output

  1. Published

    J-testing of polymers via the load separation criterion based ESIS TC4 procedure: Effect of the specimen size

    Gosch, A., Arbeiter, F. J., Agnelli, S., Berer, M., Pinter, G. & Baldi, F., Sept 2020, In: Polymer Testing. 89, September, 10 p., 106637.

    Research output: Contribution to journal › Article › Research › peer-review

  2. Published

    Measurement of interdiffusion in polymeric materials by applying Raman spectroscopy

    Bruckmoser, K., Resch, K., Kisslinger, T. & Lucyshyn, T., Sept 2015, In: Polymer Testing. 46, p. 122-133 12 p.

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    Measurement of the visual perceptibility of sink marks on injection molding parts by a new fast processing model

    Gruber, D. P., Macher, J., Haba, D., Berger, G., Pacher, G. & Friesenbichler, W., 2014, In: Polymer Testing. 33, p. 7-12

    Research output: Contribution to journal › Article › Research › peer-review

  4. Published

    Mechanical recyclability of technical biopolymers: Potential and limits

    Resch-Fauster, K., Klein, A., Blees, E. & Feuchter, M., 1 Dec 2017, In: Polymer Testing. 64.2017, December, p. 287-295 9 p.

    Research output: Contribution to journal › Article › Research › peer-review

  5. Published

    Method to characterize the damping behavior of thin passively constrained layer laminates using dynamic mechanical analysis (DMA) in shear mode

    Knapp, G., Oreski, G. & Pinter, G., 2015, In: Polymer Testing. 42, p. 215 224 p.

    Research output: Contribution to journal › Article › Research › peer-review

  6. E-pub ahead of print

    Morphological structure and mechanical properties of a nucleated Polyoxymethylene (POM) homopolymer resin processed under conventional injection molding conditions

    Schrank, T., Ramoa, B., Feuchter, M., Pinter, G., Pantani, R. & Berer, M., 7 May 2024, (E-pub ahead of print) In: Polymer Testing. 134.2024, May, 13 p., 108444.

    Research output: Contribution to journal › Article › Research › peer-review

  7. Published

    Novel approach to the measurement of the visual perceptibility of sink marks on injection molding parts

    Gruber, D. P., Berger, G., Pacher, G. & Friesenbichler, W., 2011, In: Polymer Testing. p. 651-656

    Research output: Contribution to journal › Article › Research › peer-review

  8. Published

    On the strain measurement and stiffness calculation of carbon fibre reinforced composites under quasi-static tensile and tension-tension fatigue loads

    Brunbauer, J. & Pinter, G., 2014, In: Polymer Testing. 40, p. 256-264

    Research output: Contribution to journal › Article › Research › peer-review

  9. Published

    Optimization of run parameters of Temperature Rising Elution Fractionation by the aid of a factorial design experiment

    Aust, N., Gahleitner, M., Reichelt, K. & Raninger, B., 2006, In: Polymer Testing. 25, p. 896-903

    Research output: Contribution to journal › Article › Research › peer-review

  10. Published

    Prediction of polyethylene density from FTIR and Raman spectroscopy using multivariate data analysis

    Bredács, M., Barretta, C., Castillon, L. F., Frank, A., Oreski, G., Pinter, G. & Gergely, S., Dec 2021, In: Polymer Testing. 104.2021, December, 8 p., 107406.

    Research output: Contribution to journal › Article › Research › peer-review

Previous 1 2 3 4 5 6 Next
View graph of relations