Materials science and engineering: A, Structural materials: properties, microstructure and processing, 0921-5093
Journal
| ISSNs | 0921-5093 |
|---|---|
| Additional searchable ISSN (electronic) | 1873-4936 |
111 - 120 out of 179Page size: 10
Research output
- Published
Heterogeneous nucleation in an Al-Ni-Si alloy studied using a metallic galss technique
McKay, B., Cizek, P. & Schumacher, P., 2001, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. p. 240-244Research output: Contribution to journal › Article › Research › peer-review
- Published
Heat Transfer in the Single Roller Quenching Methods
Ludwig, A., 1991, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. p. 751-754Research output: Contribution to journal › Article › Research › peer-review
- Published
Hardening and microstructure reactions in high-temperature Equal-Channel Angular Pressed Mg-Nd-Gd-Zn-Zr alloy
Li, J., Sha, G., Xu, W., Xia, K., Jie, W. & Simon, R., 2010, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 527, p. 5092-5099Research output: Contribution to journal › Article › Research › peer-review
- Published
Generalised ‘Jackson-Hunt’ Model for Eutectic Solidification at Low And Large Peclet Numbers And Any Binary Eutectic Phase Diagram
Ludwig, A. & Leibbrandt, S., 2004, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. p. 540-546Research output: Contribution to journal › Article › Research › peer-review
- Published
General Concept for a Stability Analysis of a Planar Interface under Rapid Solidification Conditions in Multicomponent Alloy Systems
Ludwig, A. & Pustal, B., 2001, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. p. 337-340Research output: Contribution to journal › Article › Research › peer-review
- E-pub ahead of print
Friction welding of selective laser melted Ti6Al4V parts
Prashanth, K. G., Damodaram, R., Maity, T., Wang, P. & Eckert, J., 3 Aug 2017, (E-pub ahead of print) In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 704.2017, September, p. 66-71 6 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
FIB damage of Cu and possible consequences for miniaturized mechanical tests
Kiener, D., Motz, C., Rester, M., Jenko, M. & Dehm, G., 2007, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 459, p. 262-272Research output: Contribution to journal › Article › Research › peer-review
- E-pub ahead of print
Fatigue crack growth behavior of a nanocrystalline low Young's modulus β-type Ti–Nb alloy
Pillmeier, S., Pippan, R., Eckert, J. & Hohenwarter, A., 4 Mar 2023, (E-pub ahead of print) In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 871.2023, 26 April, 12 p., 144868.Research output: Contribution to journal › Article › Research › peer-review
- E-pub ahead of print
Experimental and numerical investigations of the γ″ and γ′ precipitation kinetics in Alloy 718
Drexler, A. K., Oberwinkler, B., Primig, S., Turk, C., Povoden-Karadeniz, E., Heinemann, A., Ecker, W. & Stockinger, M., 6 Mar 2018, (E-pub ahead of print) In: Materials Science and Engineering A. 723.2018, 18 April, p. 314-323 10 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Evolution of misorientation distribution during warm 'abc' forging of commercial-purity titanium
Mironov, S. Y., Salishchev, G. A., Myshlyaev, M. M. & Pippan, R., 2006, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 418, p. 257-267Research output: Contribution to journal › Article › Research › peer-review
