Materials science and engineering: A, Structural materials: properties, microstructure and processing, 0921-5093
Journal
ISSNs | 0921-5093 |
---|---|
Additional searchable ISSN (electronic) | 1873-4936 |
Research output
- Published
Precipitation processes in a Mg–Zn–Sn alloy studied by TEM and SAXS
Rashkova, B., Prantl, W., Görgl, R., Keckes, J., Cohen, S., Bamberger, M. & Dehm, G., 2008, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. A494, p. 158-164Research output: Contribution to journal › Article › Research › peer-review
- Published
Enhancement in strength and thermal stability of selective laser melted Al–12Si by introducing titanium nanoparticles
Qi, J., Liu, C. Y., Chen, Z. W., Liu, Z. Y., Tian, J. S., Feng, J., Okulov, I. V., Eckert, J. & Wang, P., 10 Oct 2022, In: Materials Science and Engineering A. 855.2022, 10 October, 12 p., 143833.Research output: Contribution to journal › Article › Research › peer-review
- Published
Elevated temperature mechanical properties of novel ultra-fine grained Cu-Nb composites
Primorac, M.-M., Abad, M. D., Hosemann, P., Kreuzeder, M., Maier, V. & Kiener, D., 2015, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 625, p. 296-302Research output: Contribution to journal › Article › Research › peer-review
- Published
Transformation from continuous-to-isothermal aging applied on a maraging steel
Primig, S. & Leitner, H., 2010, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 527, p. 4399-4405Research output: Contribution to journal › Article › Research › peer-review
- Published
Influence of the heating rate on the recrystallization behavior of molybdenum
Primig, S., Leitner, H., Knabl, W., Lorich, A., Clemens, H. & Stickler, R., 2012, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 535, p. 316-324Research output: Contribution to journal › Article › Research › peer-review
- E-pub ahead of print
Friction welding of selective laser melted Ti6Al4V parts
Prashanth, K. G., Damodaram, R., Maity, T., Wang, P. & Eckert, J., 3 Aug 2017, (E-pub ahead of print) In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 704.2017, September, p. 66-71 6 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Solid solution hardening of molybdenum-hafnium alloys: Experiments and Modeling
Pöhl, C., Schatte, J. & Leitner, H., 2013, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 559, p. 643-650Research output: Contribution to journal › Article › Research › peer-review
- Published
Dynamic recrystallization of NI-base alloys-Experimental results and comparisons with simulations
Poelt, P., Sommitsch, C., Mitsche, S. & Walter, M., 2006, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. p. 306-314Research output: Contribution to journal › Article › Research › peer-review
- Published
Analysis of roughness-induced crack closure based on asymmetric crack-wake plasticity and size ratio effect
Pippan, R. & Pokluda, J., 2007, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. A462, p. 355-358Research output: Contribution to journal › Article › Research › peer-review
- Published
Influence of cold rolling on the fatigue crack growth behavior of tungsten
Pillmeier, S., Žák, S., Pippan, R. & Hohenwarter, A., 23 Feb 2021, In: Materials Science and Engineering A. 805.2021, 23 February, 12 p., 140791.Research output: Contribution to journal › Article › Research › peer-review