Materials science and engineering: A, Structural materials: properties, microstructure and processing, 0921-5093
Journal
| ISSNs | 0921-5093 |
|---|---|
| Additional searchable ISSN (electronic) | 1873-4936 |
171 - 179 out of 179Page size: 10
Research output
- Published
Effect of oxide particles on the stabilization and final microstructure in aluminium
Bachmaier, A. & Pippan, R., 2011, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. p. 7589-7595Research output: Contribution to journal › Article › Research › peer-review
- Published
Evaluation of tensile and low-cycle fatigue properties at elevated temperatures in piston aluminum-silicon alloys with and without nano-clay-particles and heat treatment
Azadi, M., Bahmanabadi, H., Grün, F. & Winter, G., 11 May 2020, In: Materials Science and Engineering A. 788.2020, 24 June, 16 p., 139497.Research output: Contribution to journal › Article › Research › peer-review
- Published
Nanoindentation and wear properties of Ti and Ti-TiB composite materials produced by selective laser melting
Attar, H., Ehtemam-Haghighi, S., Kent, D., Okulov, I. V., Wendrock, H., Bönisch, M., Volegov, A. S., Calin, M., Eckert, J. & Dargusch, M. S., Mar 2017, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 688, p. 20-26 7 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
The effect of residual stresses and strain reversal on the fracture toughness of TiAl alloys
Appel, F., Paul, J., Staron, P., Oehring, M., Kolednik, O., Predan, J. & Fischer, F.-D., 7 Oct 2017, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 709.2018, 2 January, p. 17-29 13 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Critical shapes and arrangements of carbides in high-speed tool steel
Antretter, T. & Fischer, F. D., 1 Sept 1997, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 237, 1, p. 6-11 6 p.Research output: Contribution to journal › Article › Research › peer-review
- E-pub ahead of print
Influence of high pressure torsion on microstructure evolution and mechanical properties of AZ80/SiC magnesium matrix composites
Akbaripanah, F., Sabbaghian, M., Fakhar, N., Khaleghi, A. A., Minárik, P., Veselý, J., Hung, P. T., Kapoor, G., Renk, O., Máthis, K., Gubicza, J. & Eckert, J., 20 Aug 2021, (E-pub ahead of print) In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 826.2021, 5 October, 11 p., 141916.Research output: Contribution to journal › Article › Research › peer-review
- Published
A probabilistic Kitagawa-Takahashi diagram for fatigue strength assessment of cast aluminium alloys
Aigner, R., Pusterhofer, S., Pomberger, S., Leitner, M. & Stoschka, M., 4 Feb 2019, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 745.2019, February, p. 326-334 9 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
On the mean stress sensitivity of cast aluminium considering imperfections
Aigner, R., Leitner, M. & Stoschka, M., 5 Jun 2019, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 758.2019, June, p. 172-184 13 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Yield strength prediction in Ni-base alloy 718Plus based on thermo-kinetic precipitation simulation
Ahmadi, M. R., Povoden-Karadeniz, E., Whitmore, L., Stockinger, M., Falahati, A. & Kozeschnik, E., 1 Jul 2014, In: Materials Science and Engineering A. 608, p. 114-122 9 p.Research output: Contribution to journal › Article › Research › peer-review
