Materials science and engineering: A, Structural materials: properties, microstructure and processing, 0921-5093
Journal
| ISSNs | 0921-5093 |
|---|---|
| Additional searchable ISSN (electronic) | 1873-4936 |
51 - 60 out of 179Page size: 10
Research output
- Published
Effect of tempering and deep cryogenic treatment on microstructure and mechanical properties of Cr–Mo–V–Ni steel
Yan, Z., Liu, K. & Eckert, J., 6 May 2020, In: Materials Science and Engineering A. 787.2020, 10 June, 8 p., 139520.Research output: Contribution to journal › Article › Research › peer-review
- Published
Effect of thermal treatment on microstructure in high pressure torsion (HPT) deformed nickel
Schafler, E. & Pippan, R., 2004, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 387-389, p. 799-804Research output: Contribution to journal › Article › Research › peer-review
- Published
Elevated temperature mechanical properties of novel ultra-fine grained Cu-Nb composites
Primorac, M.-M., Abad, M. D., Hosemann, P., Kreuzeder, M., Maier, V. & Kiener, D., 2015, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 625, p. 296-302Research output: Contribution to journal › Article › Research › peer-review
- E-pub ahead of print
Elucidating dynamic precipitation and yield strength of rolled Mg-Al-Ca-Mn alloy
LI, J., Zhou, X., Su, J., Breitbach, B., Chwałek, M. L., Wang, H. & Dehm, G., 14 Sept 2022, (E-pub ahead of print) In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 856.2022, 20 October, 17 p., 143898.Research output: Contribution to journal › Article › Research › peer-review
- Published
Enhanced mechanical properties of Al2O3-C refractories with silicon hybridized expanded graphite
Wang, Q., Li, Y., Jin, S., Sang, S., Xu, Y., Xu, X. & Wang, G., 2 Jan 2018, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 709, p. 160-171 12 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Enhancement in strength and thermal stability of selective laser melted Al–12Si by introducing titanium nanoparticles
Qi, J., Liu, C. Y., Chen, Z. W., Liu, Z. Y., Tian, J. S., Feng, J., Okulov, I. V., Eckert, J. & Wang, P., 10 Oct 2022, In: Materials Science and Engineering A. 855.2022, 10 October, 12 p., 143833.Research output: Contribution to journal › Article › Research › peer-review
- Published
Environmental hydrogen embrittlement associated with decohesion and void formation at soluble coarse particles in a cold-rolled Al–Cu based alloy
Safyari, M., Moshtaghi, M. & Kuramoto, S., 9 Jul 2020, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 799.2022, 2 January, 12 p., 139850.Research output: Contribution to journal › Article › Research › peer-review
- Published
Erratum to "On the experimental characterization of crystal plasticity in polycrystals"
Tatschl, A. & Kolednik, O., 2004, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. A 364, p. 384-399Research output: Contribution to journal › Article › Research › peer-review
- Published
Evaluation of tensile and low-cycle fatigue properties at elevated temperatures in piston aluminum-silicon alloys with and without nano-clay-particles and heat treatment
Azadi, M., Bahmanabadi, H., Grün, F. & Winter, G., 11 May 2020, In: Materials Science and Engineering A. 788.2020, 24 June, 16 p., 139497.Research output: Contribution to journal › Article › Research › peer-review
- Published
Evolution of misorientation distribution during warm 'abc' forging of commercial-purity titanium
Mironov, S. Y., Salishchev, G. A., Myshlyaev, M. M. & Pippan, R., 2006, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 418, p. 257-267Research output: Contribution to journal › Article › Research › peer-review
